.

I am having too much fun yanking my tubesDo that too much and you might go blind.

Firmware/software is changed by putting in different EPROMs on the controller board. I remember once trying something like Graphics 800 firmware in a Data 800 controller and it gave an error message and wouldn't work, but that was a long time ago. Maybe 808 software is swappable? I know there have been a post or two by folks saying their Data 808 installation software tried to take them through Scheimpflug adjustments which weren't there.

Mark

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

http://www.crtprojectors.co.uk/ sells the update chips for S model 808 Barcos and might have the same for non-S version. They run about $100 bucks though.....

I took a look at a BG808 and it appears there are just two EPROMs that need to be swapped.

Am I understanding you correctly, you want to put your BD808 firmware in the BG808? We keep hearing the firmware limits the input frequencies, but I haven't actually tried to put a higher BG808 frequency into a BD808 to see that it isn't allowed. Maybe you should just find a newer BG808 firmware version? My computer with my EPROM burner is currently DOA so I'm not sure I could help.

What firmware/software versions do you have in each of the projectors now?

Mark

Originally posted by Z-Photo
So,

It sounds like I would have to ship my controller board to Curt. Do you know if it is only the controller board or would I have to send the whole lot??

I will have the Scheimpflug adjustment as I swapped that hardware out.

Pete

Pete,

This is my chance to help you out this time. The firmware on the Barcos are on Eproms. If I recall (being senile I may not recall correctly), the firmware in the BG808's (NOT THE "S") that I have is 6.20, if that is later than what you have, I can update it for you, just PM me if you need it. In addition, if someone has a later version, I can make those for you too.

Bruce

Hi Guys,
The latest Barco 808s firmware which also upgrades an Iris two to an Iris3 is V7.61 available from crtprojectors.co.uk it is a single chip that plugs into the controller board.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Originally posted by Tom.W
Hi Guys,
The latest Barco 808s firmware which also upgrades an Iris two to an Iris3 is V7.61 available from crtprojectors.co.uk it is a single chip that plugs into the controller board.

It's my understanding that the "S" firmware is NOT compatible with the plain BG808 and I believe someone already mentioned in this thread that the BD won't work in a BG.

If someone has BG808 firmware later than 6.20, that would be great.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

When I get back to NY I'll take care of the firmware. As for the BD, I guess someone will have to say if they have anything higher.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Hi Guys,
The latest Barco 808s firmware which also upgrades an Iris two to an Iris3 is V7.61 available from crtprojectors.co.uk it is a single chip that plugs into the controller board.

Hi guys,

I'm really looking for this software. At crtprojectors.co.uk there have no longer EPROM’s on stock. If somebody may be have just a file for the V7.61 Software that would be sufficient. I can burn it here and if somebody else interested I can burn plenty of EPROM’s. Or if somebody have already the EPROM can send it to me to make a copy of this. May be a lot of people are as well interested to get the newer software.

Thanks

Joerg

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Damn! I guess I waited too long. I was going to order from CRTProjectors.co.uk this month once I got my new tubes in my 808s. Put me in for one who is interested in a BD808s firmware with the IRIS3 updates.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

I've had 'issues' when changing Barco software. Seems that some of the 's' software isn't compatible with non S models.

Frankly I never mess with changing software.

Just my $.02

In my case I wanted to upgrade an S model Data to the newer software for the same model. Basically it gave you IRIS3 (if you already had IRIS2) and the more advanced memory managment of the Cine series. It was the latter that I was mostly interested in. Like Z this was on my to do for at least a year :( .

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

The newest software I have for the BG808s is 7.41. This should include Iris3 as well. I will try this evening.

I've had 'issues' when changing Barco software. Seems that some of the 's' software isn't compatible with non S models.

Frankly I never mess with changing software.

Just my $.02

You can not switch software between BD and BG models. There is a second EEPROM this need a change as well. But before you do this all banks need to be blanked. Otherwise there are some instructions there are not exist in the software.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Hi again,

I have checked the 7.41 Software and the RWI 5.10. The Software still says IRIS2 but the geometry setup is working fine. Compare to the other Software 7.31 and RWI 5.10 the picture is much better. It seems there are some changes. I would also be interesting to get the Software from the Cine8 Projector. As first step the 7.61 is god enough.

But the main problem is that the people how have the software need to give this for a short time to read out the EEPROMs. :(

@Z-Photo

can you please check what versions you have

@all

The following versions I have here:
BG808s: 7.12 / 7.22 / 7.31 / 7.41 RWI 5.09 / 5.10
BG1208s: 7.22 / 7.31 RWI 5.09 / 5.10
BD808: 6.20 RWI 5.09 / 5.10

Bruce,
> If someone has BG808 firmware later than 6.20, that would be great. <

I'll check my 808G when I get home tonight, and make a note here.

- Tim

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Alas,

I thought I had recalled it being a more recent EEPROM set, but it turns out the PJ build date was back on 040495, and the ROMs are: CTRL G808 V6.10, and RWI V5.06 (both fairly old). Sorry.

- Tim

Hi,

Today I had a nice chat with a German Barco technician. This is possible to just change the Software to get IRIS3. At the end I have to buy the EPROM from Barco. As soon the software is here I will test everything. If someone is interested to get the newer software please get in contact with me. I just bought it for the BG808s.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Bruce,
> If someone has BG808 firmware later than 6.20, that would be great. <

I'll check my 808G when I get home tonight, and make a note here.

- Tim

I was going to burn an EPROM for Pete's 808, but as far as I know, V. 6.20 is the latest version for the plain BG808. The 7.xx firmware is for the BG808S.

Hi,

Today I had a nice chat with a German Barco technician. This is possible to just change the Software to get IRIS3. At the end I have to buy the EPROM from Barco. As soon the software is here I will test everything. If someone is interested to get the newer software please get in contact with me. I just bought it for the BG808s.

If you don't mind me asking how much is the chip from Barco I am interested in IRIS3 but I have an 808S Data so I am not sure the Graphics software will work for me.

If you don't mind me asking how much is the chip from Barco I am interested in IRIS3 but I have an 808S Data so I am not sure the Graphics software will work for me.

The price for the Chip is 60 Euros ( roughly 70 Dollars) If you like I can order one for you. May be you can share with other. The newest Data Software I have is 6.20 . Why you don't try the BG software? :rolleyes:

Hi,

Finally I have received now the new software. The IRIS is now more precise but so far I can see no major improvement from 7.41 to 7.61 . The biggest difference was from 7.22 to 7.31 and 7.31 to 7.41.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Not yet,

But the memory bank system is working better. I will compare both tonight (german time).

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Now that is cool.

Looks like you will have the eprom/software done just about the time I am finished with my Barkenstein PJ (LC BG 808s). :D

Pete

Wow,

What tubes do you have in your LC 808s

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Sounds like a good plan.

Sounds interesting! Take lots of pics Pete!

Kal

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Yeah the memory bank improvement is bascially what they used on the Cine series or so I am told. That was why I wanted the upgrade. Might have to call Barco to see if I can get it for the Data S series.

Z that mod project looks like fun, I will be interested to see how it turns out. Where are you getting the colored C elements from? VDC, 3m? I am assuming they are not the same as the 9" variety folks are always buying. Also it looks like the middle lens is different? And finally does the Retro hardware have scheimpflug built in? I have never seen a Retro 808 in pieces before. :)

Yep,

The Retro "box" will be here Saturday. When me and Clarence exchange christmas PJ's.

He get a NEC 6PG XTRA and I get a retro 808...

Pete

I'm going to exchange Xmas projectors with Clarence also. He's giving me his G90 and I'm giving him a 9500. :p :D

Im looking for the most up to date software for

1208s/E and 1208s/2

I want 3 copies if anyone can help.

Thank you.

Im looking for the most up to date software for

1208s/E and 1208s/2

I want 3 copies if anyone can help.

Thank you.

I can order this for you.
You need just to buy one piece the rest can be duplicated.
The price for the Chip is 60 Euros ( roughly 70 Dollars) order from Barco. May be you can share with other.

good threat,

I recently tried to upgrade a 1208s/2 that has version 7.14 to version 7.20 from a same model projector. Actually I read the version 7.20 and the RWI eprom and burned them in the same size eproms. Funny enought the original 7.14 projector starts but after a few seconds it shuts down and tries 2 more restarts.
I wonder what is really going on here, maybe the prommer I use has a problem ?
After burning , the software tells me that the data in the editor is the same as int the eprom, so no traceable faults there. anybody having a similar experience ?

good threat,

I recently tried to upgrade a 1208s/2 that has version 7.14 to version 7.20 from a same model projector. Actually I read the version 7.20 and the RWI eprom and burned them in the same size eproms. Funny enought the original 7.14 projector starts but after a few seconds it shuts down and tries 2 more restarts.
I wonder what is really going on here, maybe the prommer I use has a problem ?
After burning , the software tells me that the data in the editor is the same as int the eprom, so no traceable faults there. anybody having a similar experience ?

This may happen if you have very old software and try a newer one. You can see as well that the LED’s in the controller board doing funny things. All this happen when the new software updates the internal EEPROM values. After this everything should work normal.

unfortunately not. However the leds are not behaving in a way they should, but so far I was unable to perform the update.
Maybe you contact me at my email in german

spatz@spatz-tech.de

thanks

unfortunately not. However the leds are not behaving in a way they should, but so far I was unable to perform the update.
Maybe you contact me at my email in german

spatz@spatz-tech.de

thanks

OK,

You have a mail

good threat,

I recently tried to upgrade a 1208s/2 that has version 7.14 to version 7.20 from a same model projector. Actually I read the version 7.20 and the RWI eprom and burned them in the same size eproms. Funny enought the original 7.14 projector starts but after a few seconds it shuts down and tries 2 more restarts.
I wonder what is really going on here, maybe the prommer I use has a problem ?
After burning , the software tells me that the data in the editor is the same as int the eprom, so no traceable faults there. anybody having a similar experience ?

Did you check the "checksum" between the original and the burned EPROM?

yep the software does actually compare byte by byte between the editor and what is actually burned in the eprom. I have no idea but can somebody can confirm that he read newer versions burned them and they did work ?

I have just ordered Barco original software for the 1208s/E (and 1208s/2 maybe..)

SO very soon copies will be available here for all....

there is also a chance that I might get some cine software to try out as well....

this seemed a better idea than asking people to remove their own software ic and risk damage to it.......or worst getting lost!

......only time will tell now......

yep the software does actually compare byte by byte between the editor and what is actually burned in the eprom. I have no idea but can somebody can confirm that he read newer versions burned them and they did work ?

You might "think" they compare byte by byte, but the checksum MUST match. If the original works, there NO REASON for the copy not to work if the checksums match and there is no shift in the address'. ;)

I recently tried to upgrade a 1208s/2 that has version 7.14 to version 7.20 from a same model projector. Actually I read the version 7.20 and the RWI eprom and burned them in the same size eproms. Funny enought the original 7.14 projector starts but after a few seconds it shuts down and tries 2 more restarts.

OK....I have been playing today and had exactly the same issue.....

perfect working BD1209s
I added in correct graphics boards but kept the original controller - ALL FINE
I then wanted to add the graphics firmware so I used 7.03 1208s/2 MAIN eprom swop only - as above wont fire up, swoped RWI as well and still no go.
NEXT swop entire controller from 1208s/2 with original eproms an Hey presto it works - So to recap a 1209s running 1208s/2 controller and firmware....

NOW - That means clever f***ing Barco!

There must be an update process or clear setting as these controllers are exactly the same but wont accept the wrongor different firmware - there must be an update process that I am missing........

This was just a test as I still want to buy BG12009s latest firmware....

By the way - CAN ANYONE GET BARCO FIRMWARE - I am happy to buy it and have a backup made for others to use - I dont have an Eprom programmer but if someone wants to point me in the direction of a sensible priced one I will buy it if it will help others....

I did order through megavision BUT Im guessing hes too busy as I have not heard anything - if you are reading this please get back in touch as I have an order for a minimum of 6 units now......And I am sure there are others waiting.......

SO....

1. anyone know the correct update procedure?
2. can anyone get me Barco firmware?
3. Any fair priced eprom programmers and eproms?


Cheers, hope this will help others.........

Hi,
I can also prgram Barco EPROMS, I have the latest BG1209s firmware 7.20 on my PC and EPROM's in the desk...
So if you need some, I take 30€/pcs because EPROMS are not cheap (if you don't by 100 of them).

Greetings,
EricXh

I have two eproms here if anyone would like to copy them.A Graphics 1209s w/Iris 2 V7.03 and a Graphics 808s W/Iris 2 V7.61 they were pulled from perfectly working machines.They were replaced by V7.20 on the 1209s and V7.61 on the 808s.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Tom -

What version was the offered BG 808s - and can I call dibs?

Pete

Hi Pete,
V7.61 . I will loan it to you if you would like to make a copy.

Good, Bad, I'm the guy with the gum.

http://www.*************.com/Barco/******.jpg

Remind you of anyone?

Sorry my mistake the G808s eprom V7.61 is the new chip I purchased 6 months ago from CRT projecters before they were no longer available. I thought I had already installed it but guess not.The projector is parked on the kitchen floor under the table ;) V7.61 is the latest and greatest for the G808s Iris 3 with Sony tubes but should work fine with other tubes. Is there someone I can trust to take very good care of this new eprom and create copys for the rest here that would like the updated firmware ? I would hate to lose this one for obvious reasons.This firmware gives you the smaller text and additional memory space plus updates an Iris 2 to on Iris 3.

Speaking of Firmware...I know it's a much older PJ, but anyone know what the latest software is for a Graphics 800? I have a programmer and tons of blank EPROMS, so I would just need the binary file if it is still floating around somewhere.

One thing that would really be great, is if there was a Firmware revision table available for lots of different PJ's, showing what changes have been made between versions, kind of like when you download a BIOS update for a PC motherboard.

Anyone know a good Eprom programmer unit?

And what price?

I would be happy to produce these for people if this seemed sensible.

I enjoy a challenge! too much sometimes.......

BG1209s - mine if thats OK with you Tom.

Now I am already seeing a pattern in versions......

version 7.03 in both the G1209s and G1208s/2 has iris 2
v7.14 in G1208s/E is labelled as 1208s/2 and has iris 3

SO my guess would be BG1209s with v7.14 also has iris 3....

AS the G1208s/2 and G1208s/E are so similar to the G1209s I am guessing that ONLY the name text with in the eprom is changed......

Years ago I used to burn eproms and as part of the "copy" I used to edit the text to say what ever I wanted - so for me a simple edit to DV1208sLC would do for a laugh.....

This then means that if I got a 'prom progger that maybe I could also customise for people.....this may not of course be possible but I am guessing could be done......

So anyone care to suggest a programmer?

Somebody ? :rolleyes:

So it appears that a few AVS members already have these eprom prog units and so no need to buy one.

TODAY 3 x 1209s 7.2 and RWI 5.10 arrived - I have to test them later today.

Im still waiting on others that people here mentioned they had for me.............

So some progress here.

I got my BG 808s 7.61 today..
:D

Thanks J.

Pete

Hey can old eproms be rewritten or are these one shot only?

Pete,
I believe they can be rewritten.

Mark....

I got my BG 808s 7.61 today..
:D

Thanks J.

Pete

Hey can old eproms be rewritten or are these one shot only?


I'm glad to hear that the packed arrived. :D

Jus for your Information, the newer Barco Versions need bigger EPROM’s. :o

Hi,

EPROM

Erasable Programable Read Only Memory

Under the sticker is a "window"

remove the sticker and place eprom in an eprom eraser - this sheds UV light on the "window" and clears the eprom

So yes keep them they are of use, Im guessing here that say an early 808 series might be large enough for a late 801 series etc as there are far less options in the earlier models

I should be testing mine today.

It is essential to keep the sticker in place to avoid accidental erasure (though this has never happened to me and I used to use these on a daily basis)

That is what I remembered. It has been 10+ years since I messed with eproms (old manufacturing equipment).

I got a lot of PJ work this weekend. :eek:

Get Mike's demo 808 back together. Swap the quad in the 1208. etc....

Edit:
I have had not issues with the software (BG 808s 7.61) that I got from J.

Pete

I've got a 1208s/2 with 7.03 and would love to upgrade, either thru copying or purchasing direct. Is anyone still tinkering with these that can help?

I've got a 1208s/2 with 7.03 and would love to upgrade, either thru copying or purchasing direct. Is anyone still tinkering with these that can help?

Hi,

I have the 7.20 for a 1208s/2 here. If you are interested just send me a PM or mail.

Hi Joerg,
Today arrive the new eprom for my Barco gr 808s,
They work perfect and improve the perfformance of the proj.
Thanks!
Ruben

What's the chances someone can burn me the latest for my BG808s. Mine says 7.05(stoneage). Ready to work some-kind-a deal. Have new tubes, need new software.

Thanks, MIKE

Pete asked:
> Hey can old eproms be rewritten or are these one shot only? <

Sure, EPROMS are erasable (that's the E). One-shot burnable PROMs can't be erased or rewritten, though if an area is initially left unburned, it can be written at a later time.

- Tim

Hi,

If anybody need a software update just send me a PM or Email. I have several new versions here. Here is a short list:

BG808s V7.61 - RWI V5.10
BG1208/2 V7.20 – RWI V5.10
BG1208 V7.20 – RWI V5.10
BG1208s/2 V7.20 – RWI V5.10
BG1209 V7.20 – RWI V5.10
BD701 V2.06 – RWI 1.16
Cine7 V2.??
……..and several more

The RWI software is not mandatory to change. You need to change the RWI only if you have some problems with your RCU.

Ok.. I hate to resurrect this thread just to gripe but I guess I'm out of options at this point.

I was very excited at the opportunity to upgrade my software so I jumped on this immediately, PMing Joerg as soon as I got his response. He told me what my options were and how much it would cost. I chose the more expensive option, which was for the eeproms to be shipped as a package (rather than a letter) which would be insured and trackable. I would not ever make an international order without both of those features for obvious reasons.

On March 16th I sent Joerg the money he requested via PayPal. Everything seemed great, I heard nothing about any problems from him.

On March 27th I sent him a PM asking how things were going. I got a response on April 3rd. He said he had been on a business trip and that he would ship the EEPROMS that week.

He then sent a PM on April 10th stating that he had shipped the proms and that it would take about a week to get them. No tracking number was included. I responded to the PM requesting the tracking number. I received no response.

On April 18th I sent a slightly more irate PM asking for the tracking number. I got nothing.

On April 21st I send him a PM stating that this feels like dealing with a deadbeat ebay seller, restating that I had already paid him a decent sum of money, that he was recommended by several other AVSers for his barcosoftware services, and that if I didn't get some concrete information about the proms by monday I would take other actions to try to move this along. Yesterday I received a PM from him saying that he had just arrived from vacation, and that i would get an update later in the day.

I've heard nothing further from him so I'm doing exactly as I said. I know that griping about it isn't going to deliver some nice fresh proms to my door, but I really don't have many other options. All I know is Joerg was recommended by other AVSers, he's offered his services to this forum, it seems others have successfully gotten their proms, and I've been sitting around waiting with baited breath for some chips for well over a Month, with nary a tracking number to show for it. I know he's not a scammer but I sure do feel scammed right now..

It took me three weeks to receive mine. paid for package and tracking #, received it in padded envelope from Texas. Was in perfect shape, Worked Great. And for some reason I think my picture looks better.

I have no complaints, MIKE

Hi,

Finally I found out what happened. It seems that in Roemick’s case something goes wrong. I have send out several EEPROM’s to a US address of my friend. She distributed the Proms to you. Everything is shipped so far for those who have paid. Even Roemick’s Proms are shipped. But some letters accidentally send out without a tracking number. She has mixed up some addresses and she has only the shipping confirmation.
Finally I will ship to Roemick a new set of EEPROM’s he ordered.

I’m not interested to collect money and do nothing for it. I’m here with my real name.
I’m quite busy and not reachable all the time sometimes away from home more than two weeks. This fact may be delay some things but I will always deliver. So I hope this will solve and close the discussion here.

@ Roemick
When you receive twice the proms please be fair and send the other back to TX. Please give a feedback when you receive the new ones.

Thanks Joerg, it works perfect. MIKE

Well I'm happy to report that the proms finally came in yesterday. I was able to install and test this morning, and everything is looking good. Despite the delay I am very happy to have them!! Thank you Joerg. I'm sure my case was the exception, especially now that you have your US distribution process all set up.

If I get another set I will send them back to TX

Thanks again!!

Roemick

Are these still available?? Whats the cost??

Are these still available?? Whats the cost??

Hi,

Yes, just send me a PM or Email for more infos.

hi, Joerg,

what is the new version for BG808 (no S)? and how can i tell what version of firmware on my machine?

would you PM me a price?

thanks.

Anyone have the V 7.41 that they no longer need?

Hi,

I've got a Barco Data 708 with software V3.20. Is there a newer version out there?

Thanks,

fermion

Hi. I have a 808s crt with eprom 7.22 how much for a 7.61 iris3eprom. Thanks Ed

do you guys know whats newest for a cine 8?

I would like to get the 6.21 or 6.30 version for my 1208G but I am being told my pj will receive ic errors and is not compatible. What other features are in the menu wit that version?

In topic:

For update Barco 808 (non s) firmware two elements are needed:

1) Eprom 27C040 with latest firmware (6.30)
2) Newer version of Convergence driver module PN. R762518!!!!!

The point 2 is VERY important because exist two versions of the board with the same part number but different.

I cannot post the images because I have only this single post ... sorry

Hi,
@Decibel62
How can i tell if i have the newer board as long time both versions have similar R numbers ? PCB number maybe ?
Mine ( BG808 ) has PCB No. 780319-3 from May 1995.
Another question:
Do you know which improvement will firmware 6.30 add against 6.10 ? If is worth i will consider an upgrade....

Thanks,
Stan

How can i tell if i have the newer board as long time both versions have similar R numbers ? PCB number maybe ?
Mine ( BG808 ) has PCB No. 780319-3 from May 1995.

In "default" board there are 12 "regulations" chips in front surface and 13 in retro surface.

In "newest" board there are 14 chips in front surface and 14 in retro surface!

The part number is the same!!!!!! R762518

When I will have plus 5 posts I will insert images. ... sorry :(


(google translator .... :o )

Do you know which improvement will firmware 6.30 add against 6.10 ? If is worth i will consider an upgrade....

mmmmmmmm

I know that the old version v 6.10 not have warmup routine, is correct?

The v6.20 have warmup routine.

The v6.30 have left side regulations and seagull regulations.

Thanks for the info and sorry for my late reaction (lack of time).
You are right: no warm-up routine in the service menu, no left side and seagull correction in the geometry.
I also heard people talking about an extra tinny add-on board (R762714) for the conv.driver, in order to enable the left side and seagull options.
But if you are positive abbout the newer conv. driver and latest CTRL ( RWI ?) being enough for upgrading, i will do it.
Where can i get those, guys ? Maybe Curt ?

Cheers

But if you are positive abbout the newer conv. driver and latest CTRL ( RWI ?) being enough for upgrading, i will do it.
Where can i get those, guys ? Maybe Curt ?
Look in the controller the chip labeled CTRL 808 v.6.x0, you must to write in another eprom 27C040 the latest firmware (v.6.30) and swap it. Sorry for my english!!!! You have a PM

I also heard people talking about an extra tinny add-on board (R762714) for the conv.driver, in order to enable the left side and seagull options.

I don't know nothing of this board ... however ... new version of Convergence Driver board solve all problems!

In the next post I will try to insert some images.

In "default" board there are 12 "regulations" chips in front surface and 13 in retro surface.

In "newest" board there are 14 chips in front surface and 14 in retro surface!

The part number is the same!!!!!! R762518

Here the images finally!

The comparison between the two boards

http://decibel.altervista.org/_altervista_ht/newCD_front.jpg

http://decibel.altervista.org/_altervista_ht/newCD_retro.jpg

Some screenshots!

http://decibel.altervista.org/_altervista_ht/version01.jpg

http://decibel.altervista.org/_altervista_ht/version02.jpg

http://decibel.altervista.org/_altervista_ht/version03.jpg

http://decibel.altervista.org/_altervista_ht/version04.jpg

http://decibel.altervista.org/_altervista_ht/version05.jpg

Ale' ;)

Hi,

Very nice and usefull shots.
I see that the orbiting option is also aviable in the random access menu and the "visible yours" logo. Nice...
You don't have an extra conv.driver board for sale, do you ?

Cheers

Very nice and usefull shots.
I see that the orbiting option is also aviable in the random access menu

coooooool !!!!

"Orbiting" menu appear because I have the little sub board PN. R762268U

http://decibel.altervista.org/_altervista_ht/orbiting.jpg

http://decibel.altervista.org/_altervista_ht/version06.jpg

The orbiting sub board must be fixed into Vert. Defl.+ Sync board

and the "visible yours" logo. Nice...

ahaha :p ... the logo "Visibly yours" appear in the my custom HTPC wallpaper ....

http://decibel.altervista.org/_altervista_ht/640x480.jpg

You don't have an extra conv.driver board for sale, do you ?

Cheers

no, no, sorry .... I have bought from Hammerheadtech

Realy cool !
If the soft 6.30 is so clever then i guess it will support the iris 3 as long time the hardware is detected.
What version of RWI do you have ? Maybe 5.10 ?

If the soft 6.30 is so clever then i guess it will support the iris 3 as long time the hardware is detected.

I think Iris3 system is incompatible with BG808 (non "s"), only Iris800 can use with BG808 (non "s") for autoconvergence.

What version of RWI do you have ? Maybe 5.10 ?

I don't know ... I will check it!

Bye

What version of RWI do you have ? Maybe 5.10 ?

uh!

I have V. 5.06 :o

uh!

I have V. 5.06 :o

Thanks for looking that up.
Good news for me than, my RWI version is also 5.06.So it means i will only need the CTRL v.6.30 and the newer version of conv. driver.
Check your PM box.

I've just bought a BG 808 and the firmware is 6.10, I'd be interested in an upgrade to 6.30...

I've just bought a BG 808 and the firmware is 6.10, I'd be interested in an upgrade to 6.30...

Here the instructions! Tested and working.



For update Barco 808 (non s) firmware two elements are needed:

1) Eprom 27C040 with latest firmware (6.30)
2) Newer version of Convergence driver module PN. R762518!!!!!

The point 2 is VERY important because exist two versions of the board with the same part number but different.

OK so how do I get the 6.30 eprom?

OK so how do I get the 6.30 eprom?

You must to buy eprom 27C040 empty and burn it with a programmer.

The Willem programmer for example ...

http://www.willem.org/catalog/images/board41r.jpg

Can someone program one for me I only need the one?

Can someone program one for me I only need the one?


If you have the bin file I can program it for you. I have plenty of blank eproms.

I didn't see it until after I posted the above that you're in the U.K.

Decibel62 has already offered, thank you techman707 for the offer

Does anyone know where I may get the Later convergence board, mine is the older one??

I have the 6.30 Firmware installed and have just changed the Conv driver to the 14 chip version however now my PJ does not display correctly, I don't get the usual menu projected, there appears to be flickering from the base of each tube.

the red led is on on H Shift Focus board and all other leds are green, there were no problems before I swapped the Conv driver, I was assured the conv driver was tested and working.

There are 5 jumpers on the later Conv driver and I was wondering if anyone who has this working can tell me how their jumpers are set please? I am guessing the doner PJ may have had other features and mine does not hence they may need to changed.

Jumper numbers J622, J412, J413 , J400 and J401

any help appreciated

An update. I do have a picture but when I try to make any changes to geometry I get FAILURE I2c Error and I also get that if I try to set convergence to midpoint.

I don't get the Left side or Seagul options in the menus even though it says 6.30

Any ideas, is this anything to do with a previuosly mentioned mini-board?

So at present I cannot setup this PJ with the 2 requirements met.

mmmmmmmh .... I will look jumpers on my board. Stay tuned.

Hulio?

Hi guys,

I did not installed the EPROM yet because i don't have the new conv. driver.I think i will receive the board next week or so.
I am also curious about those jumpers, if it seems that is not that "plug-and-play".

The Jumpers setting on Convergence Driver is this.

J622 Jumper present - closed on position 2
J412 Jumper present - closed
J413 Jumper present - closed on position 1
J400 Jumper present - closed
J401 Jumper not present - open

A my friend and I have upgraded version with success and without problems.

Both we have additional "convergence on green" board.

This is a problem? I don't know :confused:

However ....

1) We wait for the Hulio's test :)
2) I will test my BG808 without Convergence on Green board and post the results

Stay tuned!

:D

I just looked at the service sheet of the conv. driver board and notice something about jumper J622.
For BarcoData 808 and RetroData 808 pins 1 and 2 must be shorted ( position 1 on PCB ) and for BarcoGraphics 808 and 1200 series pins 2 and 3 must be shorted ( position 2 ).
The chance that the other four jumpers( 400, 401, 412 and 413 ) need to be changed is small but if the board is from another type of projector, J622 must be changed.
However, set the jumpers like Decibel62 says and see if it works.
The optional convergence on green card don't have anything to do with seagull and left side, i think.The most BG808S and Cine 8 projectors do not have it.
In fact, COG card is usefull only in a two- projectors configuration (stacking ).

hi
I'm looking for RWI 5.10,
Is there anyone who can help me?

regards

Hi,

Which RWI vesion do you have at he mo?

Why do you want 5.10?

I am curious to know what you believe the RWI chip does.

Andy.

hi
MadMrH

I have v7.22 onboard and RWI 5.08 now.
I pick up new eprom a few days ego and I tried to changed software to V7.61 but after this I can't use RCU.
I think it is becouse of old RWI so I want to try v7.61 with RWI 5.10

regards