Transmission Line Isobaric Subwoofer for home. - Page 3 - AVS Forum | Home Theater Discussions And Reviews
Forum Jump: 
 6Likes
Reply
 
Thread Tools
post #61 of 64 Old 01-05-2015, 06:17 AM - Thread Starter
Senior Member
 
Gaugster's Avatar
 
Join Date: Feb 2005
Location: Chicago, IL
Posts: 432
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 63 Post(s)
Liked: 56
I have some 2 ply birch veneer. Check out post #28.

The new sub fits but with only a mm or so to spare. Same for my orbital sander. It is very much a miracle. I sized the opening bigger so that I had more room knowing that modern subs have larger motor/magnet assemblies.
Gaugster is offline  
Sponsored Links
Advertisement
 
post #62 of 64 Old 01-17-2015, 07:30 PM - Thread Starter
Senior Member
 
Gaugster's Avatar
 
Join Date: Feb 2005
Location: Chicago, IL
Posts: 432
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 63 Post(s)
Liked: 56
Some more progress on the finish..... Looking Great.....

Have to paint over the edges and some finishing touches.....
Attached Thumbnails
Click image for larger version

Name:	DSC01913.JPG
Views:	136
Size:	99.8 KB
ID:	485305   Click image for larger version

Name:	DSC01916.JPG
Views:	107
Size:	97.4 KB
ID:	485313   Click image for larger version

Name:	DSC01915.JPG
Views:	102
Size:	96.8 KB
ID:	485321   Click image for larger version

Name:	DSC01910.JPG
Views:	112
Size:	148.4 KB
ID:	485329  

Gaugster
Gaugster is offline  
post #63 of 64 Old 01-18-2015, 07:27 PM - Thread Starter
Senior Member
 
Gaugster's Avatar
 
Join Date: Feb 2005
Location: Chicago, IL
Posts: 432
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 63 Post(s)
Liked: 56
Took a lot of will power not to bolt on the amp and fire it up. But some tedious task need to be done otherwise this thing might never be "complete".

Paper thin clearance but the speaker fits.
Attached Thumbnails
Click image for larger version

Name:	DSC01939.JPG
Views:	110
Size:	115.0 KB
ID:	487090   Click image for larger version

Name:	DSC01937.JPG
Views:	112
Size:	122.6 KB
ID:	487098   Click image for larger version

Name:	DSC01926.JPG
Views:	116
Size:	127.4 KB
ID:	487106   Click image for larger version

Name:	DSC01921.JPG
Views:	117
Size:	163.3 KB
ID:	487114   Click image for larger version

Name:	DSC01918.JPG
Views:	94
Size:	116.2 KB
ID:	487122  


Gaugster
Gaugster is offline  
 
post #64 of 64 Old 01-26-2015, 07:53 PM - Thread Starter
Senior Member
 
Gaugster's Avatar
 
Join Date: Feb 2005
Location: Chicago, IL
Posts: 432
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 63 Post(s)
Liked: 56
Did some REW sweeps over the weekend. Using a UMM-6 with a Cross-Spectrum calibration.

Mic was in a stand and measured at multiple locations across the couch. Distance is over 4 meters from the transmission line subwoofer.

Have some notches centered around 56Hz and 84Hz. These might be room modes. Planning to play with the speakers to see if I can push those notches around.

My other two subs help make the 56Hz notch less. Have to mess with the mid range speakers to see what can be done with 84Hz dip.
Attached Thumbnails
Click image for larger version

Name:	couch_pos_tl.jpg
Views:	107
Size:	188.5 KB
ID:	505025  

Gaugster

Last edited by Gaugster; 01-26-2015 at 08:06 PM.
Gaugster is offline  
Sponsored Links
Advertisement
 
Reply DIY Speakers and Subs



Forum Jump: 

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off