Very-Important information if you have the "Integra DHC-80.3" ... - AVS Forum
Forum Jump: 
 
Thread Tools
post #1 of 1 Old 01-23-2013, 11:18 AM - Thread Starter
AVS Club Gold
 
tigerhonaker's Avatar
 
Join Date: Jun 2007
Location: TN. USA
Posts: 661
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Liked: 13
* Very-Important information if you have the "Integra DHC-80.3" ...


If you have the Integra DHC-80.3 and have your (Picture) setting at {Through} you need to read this Post.

The {Through} setting in the Menu, (4-5 Picture Adjust) will give you an Off-White picture.
(Not a True White)

I think the easiest way to do this is to Show the Menus involved for these settings.

Hopefully I will be able to go through these here with you to where you can follow the (Correct-Settings) for the (White-Image/Picture).

If you want to see the difference in the picture simply pull up anything with a lot of White on the screen.
Touch pause and switch between the (Through) and {Direct or Custom} picture settings.
It will be an obvious change that you will see immediately.

Note*
Before I go through the steps I should mention "Direct & Custom" both will give the same results in regards to a (True-White-Image).
It has been found that with some set ups the "Direct" setting has given (Hand Shake) issues between components.
Therefore I went with the "Custom Setting" and it did not cause any (Hand Shake) issues.

Click on Menu, 1. Input/Output Assign




1 Input/Output Assign, Click on 1. Monitor Out





1-1 Monitor Out, Go down to where it says, (Resolution) & set it to {Source}





Back-Up to Main {Menu}, go down to #4, Source Setup, click on it.





4 Source Setup, go down to #5, Picture Adjust, click on it.





4-5 Picture Adjust, See "Picture Mode", set it to {Custom}





That's it and now you have your 80.3 set to where it will not have any effect on your Image/Picture.

As I said above you can also use the "Direct" setting but in many cases it does cause {Hand-Shake Issues}.



Terry
__________________










Pre-Amp: Integra DHC-80.3
Blu-Ray Player: Integra DBS-50.3
Projector: Runco VX-11d W/Proteus 3 Lens & DHD-4 Processor
Screen: Stewart Gray Hawk 123" W/4-way remote masking
Speakers: JM Lab Utopia Mezzo Front, Center Utopia, Side Utopia, Rear Mini Utopia
Subwoofers: 4-Mirage BPS400 sitting on 4 "Auralex Great Gramma" pads
Cables: Transparent TW Plus w/Plus Bricks
Amps: Classe', 2-CA201, 3-CAM350
Power Conditioners: 1-Richard Gray RGPC-1200S, 7-RGPC-400S
Panamax MB1500 Back up Power Unit for Runco units
Cooling: 3-sets of Z-Fans
ATM (Active Thermal Management)
Cool-Stack I
Mid Atlantic: Track 50" rack slide out
Room Acoustic: Acoustic Innovations panels
Seating: Ekornes Stressless Wave
tigerhonaker is offline  
Reply Receivers, Amps, and Processors

User Tag List

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page


Forum Jump: 

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off