Denon 1913 enough to power Infinity Primus P363's - AVS Forum
Forum Jump: 
 
Thread Tools
post #1 of 6 Old 04-22-2013, 03:50 PM - Thread Starter
Newbie
 
AllWayzCustom's Avatar
 
Join Date: Apr 2013
Posts: 6
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Liked: 10
I just got a great deal on these speakers from Frys $117 ea. My reciever is an Denon 1913 that I just grabbed off of crutchfield for $374 new. My question is after purchasing this combo I found out that p363 are 4 ohm and my denon is rated for 6-16 ohm. So will I have the juice to drive these speakers and a Klipsch RW - 12D sub which I also grabbed from newegg for $279 new yesterday?
AllWayzCustom is offline  
Sponsored Links
Advertisement
 
post #2 of 6 Old 04-22-2013, 04:23 PM
585-645-1006
 
jdsmoothie's Avatar
 
Join Date: Sep 2007
Location: Orlando, FL
Posts: 43,673
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 628 Post(s)
Liked: 1374
At moderate volume levels, yes, at louder movie volume levels perhaps not.

---------------------------------
"JD" – jd@avscience.com ; shop.avscience.com ; 585-645-1006, AVScience - Authorized dealer for AV Gear 
Mon - Fri: 8am – 8pm EST (Sat/Sun too, will return call if I don't pick up)
Call for pricing on Denon, Marantz, Yamaha, Onkyo, Klipsch, Def Tech, Oppo, Parasound 
** Think the AVR is defective?  Reset the microprocessor 4-5 times. 
jdsmoothie is online now  
post #3 of 6 Old 04-22-2013, 04:26 PM - Thread Starter
Newbie
 
AllWayzCustom's Avatar
 
Join Date: Apr 2013
Posts: 6
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Liked: 10
So jdsmoothie what exactly will happen if I try to play them louder will I damage my reciever? Will it just auto shut-off to protect itself I'm fairly new to all of this so I have a lot of questions lol.
AllWayzCustom is offline  
post #4 of 6 Old 04-22-2013, 04:43 PM
585-645-1006
 
jdsmoothie's Avatar
 
Join Date: Sep 2007
Location: Orlando, FL
Posts: 43,673
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 628 Post(s)
Liked: 1374
Yup. Shuts down in protection mode, so then you simply have to ensure you don't go above that volume level again.

---------------------------------
"JD" – jd@avscience.com ; shop.avscience.com ; 585-645-1006, AVScience - Authorized dealer for AV Gear 
Mon - Fri: 8am – 8pm EST (Sat/Sun too, will return call if I don't pick up)
Call for pricing on Denon, Marantz, Yamaha, Onkyo, Klipsch, Def Tech, Oppo, Parasound 
** Think the AVR is defective?  Reset the microprocessor 4-5 times. 
jdsmoothie is online now  
post #5 of 6 Old 04-22-2013, 09:25 PM
AVS Special Member
 
M Code's Avatar
 
Join Date: Mar 2003
Location: Joshua Tree, CA
Posts: 9,856
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 90 Post(s)
Liked: 121
Quote:
Originally Posted by AllWayzCustom View Post

I just got a great deal on these speakers from Frys $117 ea. My reciever is an Denon 1913 that I just grabbed off of crutchfield for $374 new. My question is after purchasing this combo I found out that p363 are 4 ohm and my denon is rated for 6-16 ohm. So will I have the juice to drive these speakers and a Klipsch RW - 12D sub which I also grabbed from newegg for $279 new yesterday?

The latest P363 are listed @ 8 Ohms on the Infinity factory site....
It is true in the past..
Certain Infinity loudspeakers were harder to drive but the Denon should do fine..
Key point is to make sure you have at least 3-4" for free-air clearance for the L/R sides and top to prevent thermal shutdown..
The other crucial factors to consider are:
Room size, average volume level, type of source material..


Just my $0.02... 👍 😉
M Code is offline  
post #6 of 6 Old 04-23-2013, 04:43 AM - Thread Starter
Newbie
 
AllWayzCustom's Avatar
 
Join Date: Apr 2013
Posts: 6
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Liked: 10
Quote:
Originally Posted by M Code View Post

The latest P363 are listed @ 8 Ohms on the Infinity factory site....
It is true in the past..
Certain Infinity loudspeakers were harder to drive but the Denon should do fine..
Key point is to make sure you have at least 3-4" for free-air clearance for the L/R sides and top to prevent thermal shutdown..
The other crucial factors to consider are:
Room size, average volume level, type of source material..


Just my $0.02... 👍 😉

Thanks
AllWayzCustom is offline  
Reply Receivers, Amps, and Processors

User Tag List

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page


Forum Jump: 

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off