Denon 2313CI Volume Issues - AVS Forum
Forum Jump: 
 
Thread Tools
post #1 of 5 Old 08-23-2013, 07:29 AM - Thread Starter
Member
 
Spyderturbo007's Avatar
 
Join Date: Oct 2005
Posts: 151
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Liked: 10
I'm having some problems with my Denon receiver following running the Audyssey setup. For some reason, when I use different sound fields I have to turn the volume up as loud as it will go. For example, when watching a movie or TV show from my XBMC, I can turn it up to what I consider a "normal" volume (-30dB) for my viewing room. But when I switch to music, which is normally just stereo sound, I have to turn it up all the way (+18dB) to get something I can hear. I've been through the settings about 10 times now and can't figure out where the problem lies. Any ideas?

If I can't nail it down, is there a way to factory reset the receiver?
Spyderturbo007 is offline  
Sponsored Links
Advertisement
 
post #2 of 5 Old 08-23-2013, 08:51 AM
AVS Special Member
 
Knucklehead90's Avatar
 
Join Date: Nov 2008
Location: State of Confusion - 98823
Posts: 7,355
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 25 Post(s)
Liked: 101
This sounds like a setup issue. Have you run the Audyssey setup?

To reset the processor:

1 Turn off the power using ON/STANDBY.
2 Press ON/STANDBY while simultaneously pressing PRESET CHANNEL 2 and
PRESET CHANNEL 3.
3 Once the display starts flashing at intervals of about 1 second, release the two buttons.

When all else fails - RTFM!

♫♫♫ Two Channel Rules! ♫♫♫

GO SEAHAWKS!!!
Knucklehead90 is offline  
post #3 of 5 Old 08-23-2013, 09:17 AM - Thread Starter
Member
 
Spyderturbo007's Avatar
 
Join Date: Oct 2005
Posts: 151
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Liked: 10
Yes. Actually this started right after running the Audyssey setup. Everything was fine before running the setup.
Spyderturbo007 is offline  
post #4 of 5 Old 08-23-2013, 09:46 AM
AVS Special Member
 
Knucklehead90's Avatar
 
Join Date: Nov 2008
Location: State of Confusion - 98823
Posts: 7,355
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 25 Post(s)
Liked: 101
You can turn off the Audyssey processing while in stereo mode. Use Direct or Pure Direct mode.

When all else fails - RTFM!

♫♫♫ Two Channel Rules! ♫♫♫

GO SEAHAWKS!!!
Knucklehead90 is offline  
post #5 of 5 Old 08-23-2013, 09:09 PM
585-645-1006
 
jdsmoothie's Avatar
 
Join Date: Sep 2007
Location: Orlando, FL
Posts: 43,663
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 625 Post(s)
Liked: 1374
With Audyssey enabled, and reference volume set to 0db, you should never have to raise the master volume above that level (nor is it recommended to ensure there is sufficient headroom available for peaks). Do you have a sub in your setup and if yes, are all speakers set to SMALL with a minimum of an 80Hz crossover?

Also note there is a dedicated thread for Denon AVR-XX13 Owners linked in my sig. Review posts #3-6 for more helpful information.

---------------------------------
"JD" – jd@avscience.com ; shop.avscience.com ; 585-645-1006, AVScience - Authorized dealer for AV Gear 
Mon - Fri: 8am – 8pm EST (Sat/Sun too, will return call if I don't pick up)
Call for pricing on Denon, Marantz, Yamaha, Onkyo, Klipsch, Def Tech, Oppo, Parasound 
** Think the AVR is defective?  Reset the microprocessor 4-5 times. 
jdsmoothie is offline  
Reply Receivers, Amps, and Processors

Tags
Denon Avr 2313ci Receiver
Gear in this thread - 2313ci by PriceGrabber.com

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page


Forum Jump: 

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off