AVS Forum banner

The Cinemar Home Theater Construction Thread

973K views 3K replies 316 participants last post by  mcascio 
#1 · (Edited)

Electronic House 2013 Gold Award Winner
Best Home Theater $25,000 - $75,000
 
 

AVS Home Theater of the Month
 
 
SEATING
* FRONT ROW: 3 Curved Berkline 45003 Black Leather Motorized Recliners
* BACK ROW: 4 Curved Berkline 45003 Black Leather Motorized Recliners

SPEAKERS
* CENTER: M&K S-5000 THX
* FRONT LEFT/RIGHT: M&K S-5000 THX
* ATMOS TOP FRONT LEFT/RIGHT: M&K SS-150 THX
* ATMOS TOP REAR LEFT/RIGHT: M&K SS-150 THX
* SURROUND LEFT/RIGHT: M&K SS-150 THX
* BACK LEFT/RIGHT: M&K SS-150 THX
* SUB1: M&K MX-350 THX
* SUB2: HSU VTF-15H
* SUB 3 & 4: DIY Flat Pack Builds - Dayton Audio RSS460HO-4 18" Reference HO Subwoofer  4 Cubic Feet each

ROOM DIMENSIONS & MEASUREMENTS
* BEFORE WALLS: 27' Deep x 17'9" Wide (excludes theater foyer entryway)
* FINISHED ROOM AFTER SOUND PROOFING: 25'8" Deep x 16'9.5" Wide
* NOTES: The theater is being constructed in part of our unfinished basement. There is a 23" drop in the basement to allow for stadium seating.
* SHORTEST CEILING HEIGHT BEFORE CONSTRUCTION: 8'10"
* TALLEST CEILING HEIGHT BEFORE CONSTRUCTION in Drop Down area: 10'9"
* Front Row: 8'6" from Front of Seat to screen
* Back Row: 14'7" from Front of Seat to screen
* Projector: 16'2" from Lens to Screen
* Screen: 136" Wide 2.35
VIEWING DISTANCE TO BOTTOM OF SCREEN FROM CENTER FRONT ROW
* SEAT INCLINED: 10' 5 1/2"
* SEAT DECLINED: 11' 2"
 

EQUIPMENT
* RECEIVER: Denon X5200W, OLD: Denon AVR-4520CI (11.2), OLD: Onkyo NX-TR3008 (FOR SALE)
* AMP: Emotiva XPA-5 (Center, Front Left & Right, Side Surround Left & Right)
* AMP: Behringer EP4000 (2 Dayton Subs)
* AMP: (2) Dayton APA100 (Atmos Speakers Top Front & Top Rear inside Soffit)
* BLU-RAY PLAYER: Dune HD Max
* GAMING: PS3, (2) XBOX-360
* POWER CONDITIONER: Belkin PF60
* IMAGE PROCESSING: Darbee Darblet DVP5000
* STORAGE: Cinemar MLD-4000 12 TB Mass Storage Server
* PROJECTOR: Panasonic PT-AE8000U
* SCREEN: 136" Wide 2.35 AT Screen (Seymour AV)
* TABLET/iPAD/PHONE USER INTERFACE: Cinemar's MainLobby / MLServer / DVDLobby
* REMOTE CONTROL: Logitech Harmony 700
* LIGHTING CONTROL: Insteon via MainLobby
* THERMOSTAT CONTROL: Proliphix NT-20E Thermostat via MainLobby
* INTERCOM: Not sure yet - most likely go with Russound
 
CARPETING
* Masland Quadrate Times Square
 
FABRIC
* Red Walls - FR701 GOM Style 2100 (#418) Claret Accent Fabric
* Speaker Frames - FR701 GOM Style 2100 (#408) Black Fabric
* Top of Front Cabinet Below Screen & Sides of Vertical Front Cabinets Facing Screen - Protostar Self-Adhesive Flocked Light Trap Material
* Bordering Edges that the Seymour AV Screen sit's on - Black Triple Plush Velvet

SOUND PROOFING
The room above the theater is a nursery and office. One of the rooms next to the theater is a furnace room. So it's important to keep the sound out of the rooms above and prevent sound coming in from the furnace room.
Current plan of attack is to use two layers of 5/8" drywall and Green Glue with sound absorption clips. Staggered stud walls will be on any framed walls.
* Minimum 1-3/4" Solid Core Door with automatic door bottom.

PAINTED STAR CEILING
* Hand painted black light star ceiling painted by Night Sky Murals
 
VIRTUAL MOVIE POSTER
* A 40" LED TV mounted in Portrait displays the Cover Art of the currently movies along with statistics like: Number of Movies watched in theater, Minutes remaining of playing movies, movies coming soon, lbs of popcorn consumed, etc.  The user interface on the LED Movie Poster is powered by MainLobby.
 
BASS SHAKERS
Aura Pro Bass Shakers in Back Row (4 Chairs)

SOUND TREATMENT
Recycled Denim/ Titus EcoShield (1" x 4' x 50') (Bought from Vyron Corporation)

D-BOX MOTION PLATFORM
D-Box Motion Platform in Front Row (3 Chairs)


VIRTUAL (MATTERPORT) WALK-THROUGH OF CINEMAR HOME THEATER
https://my.matterport.com/show/?m=ur3p2q8Hk9r



UNFINISHED BASEMENT AREA


FINAL ATMOS SPEAKER PLACEMENT






MY ORIGINAL PROPOSED THEATER DESIGN (Top View)


MY ORIGINAL PROPOSED THEATER DESIGN (Side View)


LATEST THEATER DESIGN (Top View)


LATEST THEATER DESIGN (Side View - RESERVED)

LATEST THEATER DESIGN (3D View)







 
 
FABRICS, CARPET & PAINT INFORMATION

 
 
 
COMPOSITED 3D IMAGE WITH ACTUAL PHOTO [There is an angled divider.  The Left Upper Area is the actual photo, the right lower area is 3D]

 
FINAL ACTUAL PHOTO WITH NIGHT SKY MURAL STAR CEILING:

 
LED TV MOVIE POSTER DISPLAYS CURRENTLY PLAYING MOVIE AND ACTUAL START / END TIMES USING CINEMAR'S MAINLOBBY SOFTWARE

 
iPad Movie Selection using Cinemar Software. Also controls thermostat, lighting, projector, receiver and security.

 
THREAD INDEX
* 12.22.09 - Construction Thread Started
* 04.27.10 - Generac House Generator Installed
* 12.04.10 - Cleaned up 4 Miles of Cable in Media Rack
* 03.19.11 - Construction Lumber and Green Glue arrived, Reworked Sump Pump Area and Added Additional Breakers to Media Rack Closet
* 03.25.11 - 3D Renders of Rec Room Area outside Theater
* 03.27.11 - Framing of Interior Basement Walls Started
* 04.03.11 - Theater Framing Started, Foundation Injection Crack Repair Completed
* 04.16.11 - Illustration Showing Theater Construction using Whisper Clips, DC-04 Clips, Drywall and OSB
* 04.16.11 - Illustration Showing Theater Heating/Cooling Supply Sound Proofing
* 04.21.11 - 3D Wireframe Composite of Seats and Columns within Theater Shell
* 05.29.11 - Dead Vent Framed and Plumbing for Bar Sink Moved out of Theater
* 06.01.11 - Started Framing Soffits
* 06.04.11 - 3D Illustration of Clips and Channel Construction
* 06.06.11 - Started Framing Interior Theater Walls
* 06.08.11 - Raising the Sunken Concrete Floor Up
* 06.12.11 - Theater Room Wiring Diagram
* 06.12.11 - Suspended Sound Proofed Vent Muffler Diagram
* 06.15.11 - Started Construction of Vent Mufflers
* 06.19.11 - Ran Wiring for Speakers, Bass Shakers, Cat5 and Subs. Puddy Pads
* 06.23.11 - Can Light Backer Box Construction
* 06.23.11 - Initial Lighting Diagram
* 06.25.11 - Vent Muffler Installed using IB-3 Clips
* 06.26.11 - Corner Clamps, Acoustic Sealant, Network Thermostat Wired, R19 in Ceiling Started
* 06.29.11 - Speaker and Column Placement Diagram and Discussions
* 06.29.11 - Pipe Wrap on Vent Boots, IB-3 Clips on 2nd Vent Muffler, Instulating Vent Muffler
* 07.01.11 - 2nd Vent Muffler Installed into Soffit
* 07.01.11 - TIP: Whisper Clip Inside Corner Placement Diagram
* 07.03.11 - Hung Whisper Clips and Started Installed Hat Channel
* 07.05.11 - Sound Proofed Cold Air Return 1 and all Hat Channels Installed
* 07.07.11 - Sound Proofed Cold Air Return 2 - From the Inside of the Cold Air Return
* 07.11.11 - Tips and Tricks to hanging Whisper Clips and Hat Channels
* 07.13.11 - HVAC Items Completed: Dead Vent Inline Fan Installed and enclosed, Air Tubes installed for Vent Dampers and Arzel Zones
* 07.18.11 - Theater Insulation Nearly Complete, All Holes Caulkded and Puddy Pads on Light Gang Boxes
* 07.18.11 - Theater Foyer Sheet Rocked
* 07.31.11 - 5/8" OSB and Plywood installed on Ceiling
* 08.04.11 - 5/8" OSB Installed on Walls (First Layer)
* 08.06.11 - 5/8" Drywall and Green Glue Installed on Walls and Ceiling (Second Layer)
* 08.09.11 - Taping and Mudding Drywall Begins
* 08.10.11 - Gray Primer Applied to Drywall
* 08.12.11 - Our Newborn Arrives
* 08.13.11 - Cement Floor Cut up to Recess Electrical and Data Outlets for Back Row Seating
* 08.21.11 - Elk Security Panel Cleaned Up
* 08.22.11 - MainLobby User Interface for the Elk Security System
* 09.09.11 - Photos of Basement
* 09.21.11 - Patch Panel Cabinet Framed In and Bar Area Cabinets Installed
* 09.26.11 - 2x4x12's Added to Soffit and Stairway Platform Construction Begins
* 09.28.11 - First Row Riser Construction Started
* 09.28.11 - Granite Bar Top Installed
* 09.28.11 - DBox Alumninum Frame Assembled
* 10.04.11 - First Layer of 3/4" OSB Installed on First Row Platform
* 10.05.11 - Second Layer of 3/4" OSB Installed on First Row Platform
* 10.06.11 - Profile Illustration of Bar Construction Outside Theater
* 10.11.11 - Riser Step Framing Started
* 10.15.11 - Front Stage Framing Started
* 10.19.11 - Second Layer of 3/4" OSB Added to Front Stage and Steps
* 10.20.11 - Composite Image of Actual Photo at Stage of Construction with 3D Wireframe Render
* 10.22.11 - Filled Stage with Sand
* 10.24.11 - Composite Image of Actual Photo at Stage of Construction with 3D Render
* 10.24.11 - Insulated Areas of Front Stage and Side Steps
* 10.25.11 - Cutting OC703 and Corner Bass Traps Installed
* 10.26.11 - Projected Video onto Wall for estimating Appropriate Screen
* 10.26.11 - Nailed Two Layers of Recycled Denim to Screen Wall
* 10.27.11 - 3D Renders of Red Vs Black Soffit Underside
* 11.02.11 - Cut 16 Holes for 4" LED Can Lights
* 11.04.11 - First Coat of Benjamin Moore Starry Night Blue rolled onto Star Ceiling Area
* 11.11.11 - Can Light Housing Installed in Open Soffit
* 11.12.11 - Patch Panel Terminated
* 11.13.11 - Started 3/4" MDF Speaker Column
* 11.18.11 - Column Construnction Plans with Measurements
* 11.18.11 - Moulding Installed on Bar Cabinets
* 11.18.11 - Bar Plan with Measurements
* 11.18.11 - Rec Room Photos
* 11.21.11 - More Column Construction and Moulding
* 11.22.11 - Detailed Diagram of Mouldings and their Profiles used in the Theater
* 11.23.11 - Building a Removable Magnet Speaker Frame with Black GOM Fabric
* 12.12.11 - Spray Painting 4" LED Can Lights Black
* 12.14.11 - Installed 4" LED Can Lights
* 12.17.11 - Completed Removable Speaker Grill Frames
* 12.18.11 - Attaching Columns to the Wall
* 12.19.11 - Installing Gang Boxes for Data and Electric into Columns
* 12.26.11 - Started working on Oak Steps and Bull Nose
* 12.27.11 - Quick Tips on Cutting Curves with the Jig Saw
* 12.27.11 - Carpet VS Hard Wood on Stage Renders and Discussion
* 12.31.11 - Creating the Large Curved Bull Nose in front of the Front Row
* 01.03.12 - Started Cutting the Oak for the top of the Front Stage
* 01.08.12 - Adding 1/2" Base Shoe under Oak Steps and Bull Nose to create Rounded Underside Edge, Assembling the Front Stage Step
* 01.13.12 - Assembling the Top Front Oak Stage
* 01.16.12 - Using a Biscuit Joiner to Assemble the Front Oak Stage
* 01.21.12 - Started Attaching Lower Third 3/4" MDF Panels to Wall using Green Glue and Screws
* 01.22.12 - Finished Mounting all Columns
* 01.26.12 - Photo Comparison of Protostar, Sy Fabrics Black Plush Triple Velvet and Fidelio Velvet
* 01.29.12 - Routered Bull Nose with a 1/2" Round Over Bit on Front and 1/8" Round Over Bit on Back Side
* 02.01.12 - Started Building 45 Degree Front Corner Cabinet Frames
* 02.09.12 - Started Building Front Arched Cabinet Frame
* 02.15.12 - Notching the Divider Facers for the Front Cabinet Frame
* 02.18.12 - Front Center Cabinet Door Construction
* 02.20.12 - Composite Image of Actual Photo at Stage of Construction with 3D Render
* 02.22.12 - Front Corner Cabinet Doors Installed
* 02.23.12 - TIP: Assembling Bowed Boards during Cabinet Door Construction
* 02.27.12 - Added Base Cap Moulding to Cabinet Doors
* 03.04.12 - Magnetic Latches
* 03.11.12 - Creating a Sharped Seam Fabric Soffit
* 03.18.12 - Installed a Recessed Temperature Sensor
* 03.19.12 - Finished Sanding Bare MDF Column Edges down to 220 https://www.avsforum.com/forum/post/1470#post_21797382"
* 03.21.12 - Built Corner Pine Cap
* 03.22.12 - Applied MH Ready Patch to all joints and Screw Holes on Columns 
* 03.25.12 - Finished GG all lower wall MDF, Notched Bullnose for Baseboard, Final Installation of Bullnose Behind Front Row 
* 03.28.12 - Diagram with Dimensions Showing Construction of Bullnose and Stair Tread using Base Shoe 
* 03.31.12 - Diagram with Dimensions Showing Tall Column Construction
* 04.02.12 - Started Installing Crown Moulding around Perimeter of Room
* 04.03.12 - Coped an Inside Corner Crown Moulding
* 04.04.12 - Started Installing Chair Rail
* 04.05.12 - Composite Image of Actual Photo at Stage of Construction with 3D Render
* 04.07.12 - Started Column Trim Moulding, TIPS
* 04.09.12 - Started Installing Base Board
* 04.11.12 - Started Installing Panel Moulding
* 04.17.12 - Started Construction Fabric Panels
* 04.20.12 - Tips on Cutting GOM Fabric [Rotary Cutting Tool, Straigt Edge Clamp]
* 04.23.12 - Building a Fabric Frame around Receptacle Switches and Vents, Started Double Jamb Door Construction
* 04.27.12 - Installing Door Hinges and Door Lock
* 04.30.12 - Hanging Door and Double Jambs
* 05.04.12 - Built Patch Panel Door within a Fabric Frame
* 05.06.12 - Building Fabric Frames Surrounding Door Casing
* 05.07.12 - 3D Concepts of Potential Back Bar
* 05.08.12 - Assembling Moulding Frames for Columns using Framing Jig
* 05.14.12 - Started working on D-Box Platform top Using Two Layers of 3/4" Birch Plywood
* 05.17.12 - Built Recessed Access Panels for D-Box Actuators
* 05.22.12 - Started Installing GOM Fabric Under Soffit Light Tray
* 05.31.12 - Final Light Tray Moulding Diagram, Started Installing Soffit Mouldings
* 06.06.12 - Room Cleanup and then Started Priming the Room
* 06.07.12 - First Coat of Black Benjamin Moore Paint
* 06.17.12 - Installing Shelving Brackets for Speakers, Working on Theater Foyer Moulding, Stapled GOM Fabric to Cabinet Door
* 06.20.12 - Nearly Finished Painting
* 08.13.12 - Construction Completed
* 08.28.12 - LED TV Movie Poster Now Displays Start / End Time of Movie using MainLobby
* Working on Room Acoustics, Picture, Automation User Interface
* 11.05.13 - Dual Sealed DIY 18" Dayton Subwoofer Construction
* 11.05.13 - Dual Sealed DIY 18" Dayton Subwoofer Construction (External Thread)
* 01.13.14 - Aura Pro Bass Shaker install in Berkline Chair
 
See less See more
1 19
#831 ·

Quote:
Originally Posted by DavidK442 /forum/post/21200889


What! Halogens? Don't you know you are supposed to use non-dimming, sterile infirmary shining, mercury filled compact flourescents to save the world!
A well thought out lighting plan...like everything else in your theater.

I was hoping there'd be some decent LED's available by the time I needed bulbs for the theater. I just haven't found any yet. I wish CREE made something affordable like their 6" CR6 LED can lights. They are on sale now at Home Depot for $39.99 plus our local Electric company is giving a $25 credit per LED.
 
#832 ·
I spent tonight terminating the patch panel in the theater. For those wondering, I ended up putting in this patch panel in case I had to move my Receiver into the theater room to do mic calibration with Audyssey. I'm hoping I don't and that my mic extension cable will work but at least I've got options.


The keystones are the feeds from the Theater Rack. Now I need to put banana jacks on the cable going into the theater. If I need to put the receiver in the theater for a quick calibration, I can quickly move the banana plugs from the patch panel and into the receiver.


I ended up being short a few keystones. Looks like I need to spend more money.










I also wired in some more Insteon Dimmers that will eventually be controlled by my automation system and tablet/remote/phone. I was anxious to see how the cans looked dimmed.
 
#833 ·
Yeah. If anyone knows of any good dimmable LED's for 4" cans - please let us know. Otherwise I may need to stock pile some of the Par20 Halogen's. There's 16 in the room soffit alone which means if I don't have spares, when one goes, they all need to be replaced. I'd rather return the halogen's to recoup the expense and invest in something that works well now and will be available in the future.
 
#834 ·
I started playing around with column construction based upon materials I can actually buy vs. some random mouldings I found online months ago.


I've moved to a raised panel look which I think gives a bit more depth. However, I'm not too happy with the area between the columns. I think they are competing with the speaker columns. So I either need to offset them so they don't line up as close to the speaker columns or change the moulding itself to maybe something a bit less fancy.


I'm also thinking of using 3/4" MDF on the lower wall to create the paneled look. Any issues with this? I didn't think it would given the columns will be made from MDF.


Any thoughts?








 
#836 ·

Quote:
Originally Posted by BIGmouthinDC /forum/post/21203759


3/4 MDF works fine, I've found that putting on a quick coat of Minwax sanding sealer, then sanding will give a better finish than just priming and painting the MDF, use a dark tinted primer.


I like your design.

Perfect. Thanks for the expert advice.


Regarding the columns. Carpet will come after the columns are in place. Should I elevate the columns 3/4" off the ground or just rest the MDF right on the concrete? I'm currently planning on a 1/2" pad and the Masland carpet.
 
#837 ·

Quote:
Originally Posted by mcascio /forum/post/21203953


Perfect. Thanks for the expert advice.


Regarding the columns. Carpet will come after the columns are in place. Should I elevate the columns 3/4" off the ground or just rest the MDF right on the concrete? I'm currently planning on a 1/2" pad and the Masland carpet.

I would lay the baseboard molding after the carpet therefore it would be ok to put the MDF right to the ground.


Curious about the carpet, does it go right on top of the concrete?
 
#838 ·

Quote:
Originally Posted by mcascio /forum/post/21202131


I was hoping there'd be some decent LED's available by the time I needed bulbs for the theater. I just haven't found any yet. I wish CREE made something affordable like their 6" CR6 LED can lights. They are on sale now at Home Depot for $39.99 plus our local Electric company is giving a $25 credit per LED.

Just saw these at Lowes today. They had a display booth with the lights on a dimmer. 4-6"

http://www.lowes.com/pd_78215-3-7064...hts&facetInfo=
 
#840 ·

Quote:
Originally Posted by Larry M /forum/post/21204605


I would lay the baseboard molding after the carpet therefore it would be ok to put the MDF right to the ground.


Curious about the carpet, does it go right on top of the concrete?

I don't think I would put MDF right on top of concrete. It, just like drywall, can absorb moisture from the concrete. I'd try and keep if off the ground 1/2" or so.
 
#841 ·

Quote:
Originally Posted by BllDo /forum/post/21205475


I don't think I would put MDF right on top of concrete. It, just like drywall, can absorb moisture from the concrete. I'd try and keep if off the ground 1/2" or so.

I don't think it'll be too much of an issue, but you're right and isn't worth the headache if it does swell
 
#843 ·
I thought I'd take a stab at the columns. Was going fairly well except my jig saw couldn't seem to cut a straight line while cutting out the speaker areas. The blade seemed to have a mind of it's own.


Finally it just died on me. Looks like I'll need to pick up a new one. Any recommendations?

 
#846 ·

Quote:
Originally Posted by cdika17 /forum/post/21209085


gorgeous! Hope you don't mind if i steal a few idea's, starting the demo and rebuild of my theater soon.

Thanks. Have at her. I've tried to share as much details in hopes that it will save others time and thought. Good luck with your rebuild.


As a side note. 3/4" MDF 8x4 is heavy when you are loading/unloading by yourself.
 
#847 ·

Quote:
Originally Posted by mcascio /forum/post/0


I thought I'd take a stab at the columns. Was going fairly well except my jig saw couldn't seem to cut a straight line while cutting out the speaker areas. The blade seemed to have a mind of it's own.


Finally it just died on me. Looks like I'll need to pick up a new one. Any recommendations?

The Bosch jigsaws and newer blades are unbeatable IMO, unless you buy the Festool which is big bucks.
 
#849 ·

Quote:
Originally Posted by mcascio /forum/post/21212441


Funny you should say that. I ended up ordering the Bosch 1590. It seemed to have gotten good reviews. Hopefully it's delivered by the weekend.

I forget the model #, but the old Bosch used to be considered the best jig saw. The new one (same model #) isn't as good as the original but still considered great. I'll end up ordering the same one when the time comes



EDIT: you bought the one I was describing above, nice purchase
 
#851 ·

Quote:
Originally Posted by mcascio /forum/post/21214772


Thanks Larry for confirming. The Bosch should make column construction much faster and more enjoyable.

I was very tempted to order it today, I need a new one as mine has crapped out...but I won't be starting the theater for a few months so I can put it on the Christmas wish list
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top