AVS › AVS Forum › Video Components › Home Theater Computers › EDID Overrides to solve bitstreaming issues for ATI 5xxx's
New Posts  All Forums:Forum Nav:

EDID Overrides to solve bitstreaming issues for ATI 5xxx's - Page 101

post #3001 of 3568
3/3/12 at 3:26pm
Thread Starter 
Are Dolby TrueHD and DTSHD listed on the "Supported Formats" Window for the AMD HDMI audio device? If so then the problem is with TMT5. Try reinstalling (uninstall/install) the software given that there is a new graphic card.
Reply
Reply

AVS Top Picks

post #3002 of 3568
3/3/12 at 6:24pm
Quote:
Originally Posted by Tulli View Post

Are Dolby TrueHD and DTSHD listed on the "Supported Formats" Window for the AMD HDMI audio device? If so then the problem is with TMT5. Try reinstalling (uninstall/install) the software given that there is a new graphic card.

Yes they are. I was able to bitstream initially after installing the card (1st thing I checked otherwise I would have rma'd it). I'll try reinstalling Tmt5 again, thanks.
Reply
Reply
post #3003 of 3568
3/4/12 at 2:10pm
Hi, I have a Panasonic TV (TH-42U30Q) and a Samsung home theatre system (HT-D4500). I'm trying to get 5.1 channel audio when I plug in a laptop via HDMI straight to the TV (Samsung has no HDMI input :/ ) but it's only detected 2 channels. I'm hoping I can use an EDID override to enable 6 channel audio which will hopefully get passed through to the Samsung. I read that most TVs only pass through 2 channels from HDMI, but i'm trying my luck.

I've attached my moninfo realtime data. It currently shows this audio:

CE audio data (formats supported)
LPCM 2-channel, 16-bit at 32/44/48 kHz

I'd like it to be something like the second sample file:

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48/88/96/176/192 kHz
LPCM 6-channel, 16/20/24 bit depths at 32/44/48/88/96 kHz
AC-3 6-channel, 448k max. bit rate at 32/44/48 kHz
AAC 6-channel, 384k max. bit rate at 32/44/48 kHz
DTS 6-channel, 1536k max. bit rate at 32/44/48 kHz

CE speaker allocation data
Channel configuration.... 5.1
Front left/right......... Yes
Front LFE................ Yes
Front center............. Yes
Rear left/right.......... Yes
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
Rear LFE................. No

Is someone able to edit the EDID? Is this worth trying?

 

dspinfo.zip 0.3154296875k . file
Reply
Reply
post #3004 of 3568
3/4/12 at 3:25pm
Thread Starter 
Quote:
Originally Posted by lravs View Post
Hi, I have a Panasonic TV (TH-42U30Q) and a Samsung home theatre system (HT-D4500). I'm trying to get 5.1 channel audio when I plug in a laptop via HDMI straight to the TV (Samsung has no HDMI input :/ ) but it's only detected 2 channels. I'm hoping I can use an EDID override to enable 6 channel audio which will hopefully get passed through to the Samsung. I read that most TVs only pass through 2 channels from HDMI, but i'm trying my luck.

I've attached my moninfo realtime data. It currently shows this audio:

CE audio data (formats supported)
LPCM 2-channel, 16-bit at 32/44/48 kHz

I'd like it to be something like the second sample file:

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48/88/96/176/192 kHz
LPCM 6-channel, 16/20/24 bit depths at 32/44/48/88/96 kHz
AC-3 6-channel, 448k max. bit rate at 32/44/48 kHz
AAC 6-channel, 384k max. bit rate at 32/44/48 kHz
DTS 6-channel, 1536k max. bit rate at 32/44/48 kHz

CE speaker allocation data
Channel configuration.... 5.1
Front left/right......... Yes
Front LFE................ Yes
Front center............. Yes
Rear left/right.......... Yes
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
Rear LFE................. No

Is someone able to edit the EDID? Is this worth trying?
I've attached the EDID override but note that 2-channels uncompressed audio (2-LPCM) is the max possible for S/PDIF bandwith. You can only send 5.1 compressed audio (e.g. AC3 or DTS) over S/PDIF. Read first post or search through the thread for more info.

AFAIK there's no way of sending 6-channel AAC. Only possibility is real-time encoding to DD or DTS (or 2-LPCM).

 

Panasonic TH-42U30Q+5.1AC3&DTS.zip 1.25390625k . file
Reply
Reply
post #3005 of 3568
3/5/12 at 2:18pm
Makes sense. Well thanks for the override but I'm getting some weird display issues now. I can't set screen res any higher than 720p else i get a blank screen. Playback devices still shows Panasonic-TV with max 2 channels.

moninfo shows the attached under registry-active - i thought this looked weird since there's no audio info in there. It may be to do with my previous attempt to install my own override which didn't work.

 

moninfo.txt 7.5244140625k . file
Reply
Reply
post #3006 of 3568
3/6/12 at 7:32pm
Hi i have a problem i hope you can help me !

I had a ATI HD5670 card and used ATI HDMI Driver 2.67 from Realteks Page and it worked perfectly with Dolby Home Theater !

Yesterday i bought a ATI HD7770 card and installed it with ATI HDMI Driver 2.67 it says not connected. However if i install it with AMD HDMI Driver it works,says connected but i cant use it with Dolby Home Theater.I wanna be able to use it with Dolby Home Theater.
Is there any way to make the ATI HDMI Driver force connect ?Maybe alter INF file?
Maybe i need an EDID file ,if so can you make one?
I have a ONKYO TXNR609 and a Samsung Smart TV UE40D8005 [3D TV].
Please try help me guys !I think my card HD7770 is so new that Realtek needs to update that HDMI driver 2.67 its from december 2011,and when i wrote to them.The didnt want to help.Sorry for my bad english and also if i posted this wrong.
Reply
Reply
post #3007 of 3568
3/7/12 at 2:42am
Thread Starter 
Quote:
Originally Posted by Hoggens View Post

Hi i have a problem i hope you can help me !

I had a ATI HD5670 card and used ATI HDMI Driver 2.67 from Realteks Page and it worked perfectly with Dolby Home Theater !

Yesterday i bought a ATI HD7770 card and installed it with ATI HDMI Driver 2.67 it says not connected. However if i install it with AMD HDMI Driver it works,says connected but i cant use it with Dolby Home Theater.I wanna be able to use it with Dolby Home Theater.
Is there any way to make the ATI HDMI Driver force connect ?Maybe alter INF file?
Maybe i need an EDID file ,if so can you make one?
I have a ONKYO TXNR609 and a Samsung Smart TV UE40D8005 [3D TV].
Please try help me guys !I think my card HD7770 is so new that Realtek needs to update that HDMI driver 2.67 its from december 2011,and when i wrote to them.The didnt want to help.Sorry for my bad english and also if i posted this wrong.

Post both real-time EDIDs and I'll produce a merged EDID override (see 1st. post for instructions). Of course, with your new card use the native AMD HDMI driver & not the realtek.
Reply
Reply
post #3008 of 3568
3/8/12 at 2:13pm
Hello,
I'm trying to merge data from my Sony KDL46EX521 and my 5.1 Sony A/V system but unfortunately, my A/V system does not have an HDMI input so I cannot analyze it. I do know that it supports 5.1 DD, DTS, and Pro Logic II. Can anyone help me add this data to my TV's moninfo data? Here is what it currently shows:

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz
AC-3 6-channel, 640k max. bit rate at 32/44/48 kHz

CE speaker allocation data
Channel configuration.... 2.0
Front left/right......... Yes
Front LFE................ No
Front center............. No
Rear left/right.......... No
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
Rear LFE................. No

Thank you for your help!

 

SONYKDL46EX521.zip 1.2197265625k . file
Reply
Reply
post #3009 of 3568
3/8/12 at 4:11pm
Thread Starter 
Quote:
Originally Posted by n64_ali View Post
Hello,
I'm trying to merge data from my Sony KDL46EX521 and my 5.1 Sony A/V system but unfortunately, my A/V system does not have an HDMI input so I cannot analyze it. I do know that it supports 5.1 DD, DTS, and Pro Logic II. Can anyone help me add this data to my TV's moninfo data? Here is what it currently shows:

CE audio data (formats supported)
LPCM 2-channel, 16/20/24 bit depths at 32/44/48 kHz
AC-3 6-channel, 640k max. bit rate at 32/44/48 kHz

CE speaker allocation data
Channel configuration.... 2.0
Front left/right......... Yes
Front LFE................ No
Front center............. No
Rear left/right.......... No
Rear center.............. No
Front left/right center.. No
Rear left/right center... No
Rear LFE................. No

Thank you for your help!
Number of channels is correct for uncompressed audio over S/PDIF. Please read previous posts on the subject a/o update on 1st. post.

I've only added DTS capability to the Sony TV EDID.

 

SONY KDL46EX521+5.1AC3&DTS.zip 1.2197265625k . file
Reply
Reply
post #3010 of 3568
3/8/12 at 4:25pm
Quote:
Originally Posted by Tulli View Post

Number of channels is correct for uncompressed audio over S/PDIF. Please read previous posts on the subject a/o update on 1st. post.

I've only added DTS capability to the Sony TV EDID.

Wow! Thanks for the very prompt reply. Very much appreciated. I will be sure to test this once I get home. Just a quick question though: I had read your first post where you said that streaming 6-channel uncompressed audio through SPDIF is impossible, which is fine. However, my receiver also supports 5.1 Dolby Digital (which is what my Cable PVR and PS3 use.) Any way I can add this to the EDID as well? Thanks again for your help.
Reply
Reply
post #3011 of 3568
3/8/12 at 6:32pm
Thread Starter 
Quote:
Originally Posted by n64_ali View Post

Wow! Thanks for the very prompt reply. Very much appreciated. I will be sure to test this once I get home. Just a quick question though: I had read your first post where you said that streaming 6-channel uncompressed audio through SPDIF is impossible, which is fine. However, my receiver also supports 5.1 Dolby Digital (which is what my Cable PVR and PS3 use.) Any way I can add this to the EDID as well? Thanks again for your help.

No need of it as it was already present.
Reply
Reply
post #3012 of 3568
3/9/12 at 8:47am
Quote:
Originally Posted by Tulli View Post

No need of it as it was already present.

Well, I updated my driver with your file and it shows up as EDID Override so I know that it's working. When I check the Sound Options however, my Max Number of Supported Channels is 2, although I see DTS has been added to the Encoded Formats list.

In any case, with some tinkering in MPC HC and AC3Filter, I have 5.1 surround sound! Thank you immensely for your help.
Reply
Reply
post #3013 of 3568
3/9/12 at 2:48pm
I'm trying to get my TV to pass thru DTS / AC-3 to my receiver instead of just sending stereo. Sadly i've already installed an override file from the 1st post. So getEDID is now showing a denon instead of my LG TV. Are the Files still usable?

 

GetEDID.zip 1.2509765625k . file
Reply
Reply
post #3014 of 3568
3/9/12 at 4:48pm
Thread Starter 
Quote:
Originally Posted by disaster123 View Post

I'm trying to get my TV to pass thru DTS / AC-3 to my receiver instead of just sending stereo. Sadly i've already installed an override file from the 1st post. So getEDID is now showing a denon instead of my LG TV. Are the Files still usable?

Uninstall the EDID override and use moninfo to capture the real-time EDID (see 1st. post for instructions).
Reply
Reply
post #3015 of 3568
3/9/12 at 9:01pm
Hi Tulli !
Here is my real-time EDIDs on my ONKYO TX NR 609 and Samsung UE40D8005.
Thanks for helping !

 

EDID.zip 2.1689453125k . file
Reply
Reply
post #3016 of 3568
3/10/12 at 5:27am
Thread Starter 
Quote:
Originally Posted by Hoggens View Post
Hi Tulli !
Here is my real-time EDIDs on my ONKYO TX NR 609 and Samsung UE40D8005.
Thanks for helping !
Captures only included the base block, so I had to use the extended block from compatible devices in my EDID DB for the mod.

 

SamsungUE40D8005 - ONKYO TX-NR609.zip 1.3095703125k . file
Reply
Reply
post #3017 of 3568
3/10/12 at 8:13pm
Quote:
Originally Posted by Tulli View Post

Captures only included the base block, so I had to use the extended block from compatible devices in my EDID DB for the mod.

????????? LOL I understand 0 of what you just said but big THANKS for
the EDID files Tulli !
Reply
Reply
post #3018 of 3568
3/14/12 at 10:14am
Hi, I would like to please files INF for LG 42PJ350 and ONKYO TX-SR308. Thanks in advance
Reply
Reply
post #3019 of 3568
3/14/12 at 3:42pm
Thread Starter 
Quote:
Originally Posted by guliwer View Post

Hi, I would like to please files INF for LG 42PJ350 and ONKYO TX-SR308. Thanks in advance

Capture and post the real-time EDID of the LG TV and I'll produce the required mod. See 1st. post for instructions.
Reply
Reply
post #3020 of 3568
3/16/12 at 3:17pm
It's my real-time EDID.

 

EDID.zip 2.296875k . file
Reply
Reply
post #3021 of 3568
3/16/12 at 3:35pm
Thread Starter 
Quote:
Originally Posted by guliwer View Post
It's my real-time EDID.
...

 

LG 42PJ350R - ONKYO TX-SR308.zip 1.2880859375k . file
Reply
Reply
post #3022 of 3568
3/18/12 at 4:11pm
Tulli or anyone here that can help me an EDID override to get 3D to pass through my HK avr254 receiver to my Sony KDL-60EX720 TV.

Thanks in advance!

 

HK AVR254 - Sony KDL-60EX720.zip 2.462890625k . file
Reply
Reply
post #3023 of 3568
3/18/12 at 4:28pm
Thread Starter 
Quote:
Originally Posted by thor777 View Post

Tulli or anyone here that can help me an EDID override to get 3D to pass through my HK avr254 receiver to my Sony KDL-60EX720 TV.

Thanks in advance!

Did you already check 1st post for latest update on 3D? Basically, to get HD-audio you need separate connections.
Reply
Reply
post #3024 of 3568
3/19/12 at 7:32am
So using an override will not pass HD-audio to the receiver? My video card can't bitstream HD-audio anyway so I just send multi-channel PCM to my receiver. Is it possible for you to create the override for me anyway as I want to do some testing with my current setup.

Thanks in advance.
Reply
Reply
post #3025 of 3568
3/19/12 at 10:53am
Hi ,Tulli . I used your SamsungUE40D8005 - ONKYO TX-NR609.zip on previous attched with my Samsung TV UA46C6200 and AVR TX-NR609. But the problem is there is no any dts or dolby on avr's display. could you please hep=lp me an EDID Override for my system.

TV - UA46C6200
AVR - TX-NR609

Thanks in advance.
Reply
Reply
post #3026 of 3568
3/19/12 at 12:44pm
Thread Starter 
Quote:
Originally Posted by thor777 View Post
So using an override will not pass HD-audio to the receiver? My video card can't bitstream HD-audio anyway so I just send multi-channel PCM to my receiver. Is it possible for you to create the override for me anyway as I want to do some testing with my current setup.

Thanks in advance.
...

 

Sony - KDL-60EX720 - HK-AVR254.zip 1.2890625k . file
Reply
Reply
post #3027 of 3568
3/19/12 at 12:48pm
Thread Starter 
Quote:
Originally Posted by mnkk View Post

Hi ,Tulli . I used your SamsungUE40D8005 - ONKYO TX-NR609.zip on previous attched with my Samsung TV UA46C6200 and AVR TX-NR609. But the problem is there is no any dts or dolby on avr's display. could you please hep=lp me an EDID Override for my system.

TV - UA46C6200
AVR - TX-NR609

Thanks in advance.

Should work for your setup. Are all formats listed on the "Supported Formats" window of the HDMI audio device? Also, what is your display adapter? Which player are you using?
Reply
Reply
post #3028 of 3568
3/19/12 at 1:11pm
Quote:
Originally Posted by Tulli View Post

Should work for your setup. Are all formats listed on the "Supported Formats" window of the HDMI audio device? Also, what is your display adapter? Which player are you using?

Readon HD 5750 contain all support dolby trueHD and DTS HD MA format.
Also HDMI audio device pass through.
player : daum potplayer and pass through setting Dolby true HD and DTS HD MA via HDMI.
I don't anywhere els to set.
Reply
Reply
post #3029 of 3568
3/19/12 at 1:20pm
Thread Starter 
Quote:
Originally Posted by mnkk View Post

Readon HD 5750 contain all support dolby trueHD and DTS HD MA format.
Also HDMI audio device pass through.
player : daum potplayer and pass through setting Dolby true HD and DTS HD MA via HDMI.
I don't anywhere els to set.

So all audio formats show up on the "Supported Formats" panel of the HDMI audio device properties? If so there's no EDID detection issue. Problem should be Potplayer related but I can't help you with that.
Reply
Reply
post #3030 of 3568
3/19/12 at 1:32pm
Quote:
Originally Posted by Tulli View Post

...

Thanks a bunch, Tulli! =)
Reply
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Home Theater Computers

AVS Top Picks

AVS › AVS Forum › Video Components › Home Theater Computers › EDID Overrides to solve bitstreaming issues for ATI 5xxx's