or Connect
AVS › AVS Forum › Display Devices › Screens › New ranges of Monoprice screens seem to be coming soon
New Posts  All Forums:Forum Nav:

New ranges of Monoprice screens seem to be coming soon - Page 9

post #241 of 573
I LOVE my monoprice variable format 106 (white in light controlled room). FULL DISCLOSURE, it's the first I've had beyond the screen on a stand for slides 50 years ago I'm using a Epson 1350 at about 12'
post #242 of 573
I ordered the 120" multi-format yesterday. I think I got the last one - it says out of stock now. I was not successful getting the assembly manual from anyone here, but monoprice was kind enough to email it to me. So, here it is for anyone else interested:

http://www.2shared.com/document/cFun...979707971.html

.
post #243 of 573
Has anyone tried to add motors to the masking system. I just ordered the 106" grey and enjoy tinkering, but the manual is very vague as to how the masking system works.
post #244 of 573
Yeah - best I can gather from the directions, the masking system is pre-assembled into the upper and lower frame bars.
post #245 of 573
I'm almost ready to pull the trigger on one of these screens.

I'm thinking of one of these: (106' Grey)
http://www.monoprice.com/products/pr...seq=1&format=2

Front row seating (11 ft from screen)
Second row seating (16 ft from screen)

Or do you guys think a 120' would be better?
post #246 of 573
I had originaly thought a 106 would be enough for me. Then I bought the projector and just shot it on the wall. I have the same sitting as you and I would go 120. Even my wife likes it at 120. She said 106 was way to small.
post #247 of 573
Just purchased a Monprice 133" Fixed Grey Screen to go with my Epson 3010 and later my 6010. They shipped fast. The assembly and install went without a hitch. The quality is pretty goood. the picture looks great. My only complaint is their shipping cost...they are 2-3X more than everyone elses! I needed to order another screen ~ 106", but just couldn't overpay for shipping again. Hoping my gamble with the other vendor pays off.
post #248 of 573
Quote:
Originally Posted by JamesVG81 View Post

I had originaly thought a 106 would be enough for me. Then I bought the projector and just shot it on the wall. I have the same sitting as you and I would go 120. Even my wife likes it at 120. She said 106 was way to small.

Wow that's good to know and you might have just saved me from making bad decision. Thanks for the info.
post #249 of 573
Yea I would always sagest shooting on a wall first to see what size you like. I just stuck mine on a latter and moved it back till I was happy with the size. Then messured what was on the wall. I really thought being that close to a 120 I would be moving my eye's around the screen alot but I'm really happy with the size.
post #250 of 573
I'm now interested in the 2:35:1 aspect for an electric tensioned screen and I don't think Monoprice offers them in that configuration? Anyone know who has them/
post #251 of 573
Quote:
Originally Posted by Earl H View Post

Just purchased a Monprice 133" Fixed Grey Screen to go with my Epson 3010 and later my 6010. They shipped fast. The assembly and install went without a hitch. The quality is pretty goood. the picture looks great. My only complaint is their shipping cost...they are 2-3X more than everyone elses! I needed to order another screen ~ 106", but just couldn't overpay for shipping again. Hoping my gamble with the other vendor pays off.

The shipping is outrageous, but you have to look at the overall cost. The price for the screen you are getting is way under market rate. These screens are made by Grandview. If you were to purchase a Grandview screen elsewhere you would pay way more than the total of the screen and shipping from Monoprice.
post #252 of 573
Natural
Brightness -11
Contrast 8
Color Saturation 0
Tint -2
Sharpness Advanced (All 4 Settings) 0
Abs. Color Temp. 6500K

Advanced...

Gamma Custom 0 -6 -7 -8 -7 -7 -7 -8 5

RGB
Offset R 6
Offset G 0
Offset B 23
Gain R -2
Gain G 0
Gain B -25

RGBCMY
R 0 -13 -7
G -37 -49 48
B -7 10 -6
C 0 -41 31
M -16 -9 -16
Y -3 -9 8

Power Consumption ECO
Auto Iris Normal

Signal [Advanced]
Noise Reduction Off
EPSON Super White Off
Overscan Off
HDMI Video Range Expanded
post #253 of 573
Quote:
Originally Posted by Droid6 View Post

Natural
Brightness -11
Contrast 8
Color Saturation 0
Tint -2
Sharpness Advanced (All 4 Settings) 0
Abs. Color Temp. 6500K

Advanced...

Gamma Custom 0 -6 -7 -8 -7 -7 -7 -8 5

RGB
Offset R 6
Offset G 0
Offset B 23
Gain R -2
Gain G 0
Gain B -25

RGBCMY
R 0 -13 -7
G -37 -49 48
B -7 10 -6
C 0 -41 31
M -16 -9 -16
Y -3 -9 8

Power Consumption ECO
Auto Iris Normal

Signal [Advanced]
Noise Reduction Off
EPSON Super White Off
Overscan Off
HDMI Video Range Expanded

Why did you choose to start from natural on Eco? Did you use a tool for calibrating or eyeball it?
post #254 of 573
The UPS tracking status for my screen says:

12/05/2011An incident has occurred which may result in a service delay

I don't like the sound of that at all.
post #255 of 573
Quote:
Originally Posted by slybarman View Post


Why did you choose to start from natural on Eco? Did you use a tool for calibrating or eyeball it?

I used CalMan and a Chroma5 colorimeter, if anybody came at me with that many numbers and said they eyeballed it I would laugh my ass off. I used Natural because colors were more in tune than Cinema and Eco because the increase in brightness Normal gives isn't worth the noise.
post #256 of 573
OK - thank you. This was an Epson 8350, right? I will give your settings a try when I get my screen. I do not know if Epsons have the same problem, but when I had a Panasonic projector (AX200) people who used Eco mode long-term ran into issues with the bulb flickering after some time.

Do you know how many lumens you were getting after calibration in this mode?
post #257 of 573
Quote:
Originally Posted by slybarman View Post

OK - thank you. This was an Epson 8350, right? I will give your settings a try when I get my screen. I do not know if Epsons have the same problem, but when I had a Panasonic projector (AX200) people who used Eco mode long-term ran into issues with the bulb flickering after some time.

Do you know how many lumens you were getting after calibration in this mode?

I haven't heard that about the Epson's and I didn't look at the lumens I was getting. I should have printed a report, maybe I'll go back and retake measurements and post a report but I can't promise anything.
post #258 of 573
Oops... Brightness should be -11. slybarman can you change it in the post you quoted my settings so nobody gets the wrong information?
post #259 of 573
Quote:
Originally Posted by Droid6 View Post

I haven't heard that about the Epson's and I didn't look at the lumens I was getting. I should have printed a report, maybe I'll go back and retake measurements and post a report but I can't promise anything.

There are some reports in the 8350 thread of people getting flicker in prolonged eco mode use, but it seems to go away if the projector is run in normal mode for a few hours.
post #260 of 573
Quote:
Originally Posted by slybarman View Post

There are some reports in the 8350 thread of people getting flicker in prolonged eco mode use, but it seems to go away if the projector is run in normal mode for a few hours.

I haven't had an issue yet. I think I have about 300 hours or so on my projector and it's always in Eco.
post #261 of 573
Quote:
Originally Posted by Droid6 View Post

Shoot any questions you have and I'll answer them the best I can.

Thanks for posting up your experience and calibration details. I have an 8350 as well, and am contemplating what to do for a screen (DIY or buy one), so this is useful to me.

Q: Why did you choose a white screen vs a grey one? Do you think a grey one would or would not be suitable for this projector?
post #262 of 573
Quote:
Originally Posted by Gertjan View Post

Thanks for posting up your experience and calibration details. I have an 8350 as well, and am contemplating what to do for a screen (DIY or buy one), so this is useful to me.

Q: Why did you choose a white screen vs a grey one? Do you think a grey one would or would not be suitable for this projector?

If you're going to go 120" then I would definitely not get a grey screen as the image will probably be too dim. At 100" or less I would say you could get away with a grey screen. Also consider what your viewing environment will be like. If your room can be light controlled and you have darker walls then white is your best bet.
post #263 of 573
Quote:
Originally Posted by Droid6 View Post

If you're going to go 120" then I would definitely not get a grey screen as the image will probably be too dim. At 100" or less I would say you could get away with a grey screen. Also consider what your viewing environment will be like. If your room can be light controlled and you have darker walls then white is your best bet.

Room is light controlled, and i'll be painting the walls and ceiling a dark color. I can do a screen up to about 100". Just realized that 106" is the smallest fixed screen they have, and i don't think i have the space / throw distance to pull that off
post #264 of 573
I bought the 133" recessed, tab-tensioned white screen back in June. I was so excited to get it and then it came in a 12.5" box that was over 200 lbs. My brothers and I lugged it upstairs to my media room. And I got lazy and left it there since. lol
Five months later this past weekend I finally got around to mounting it. Had to cut through my ceiling sheetrock, etc. It was a lot bigger than I expected. The stats on the manual and website are either incorrect or I measured 10 times incorrectly. They say measure twice and cut once. I measured 10 times and still didn't cut wide enough. Once I got around to mounting it was still too wide. My room is 18'x12' and the top has some wood crown molding. The screen was so wide I actually had to cut an inch off my crown molding. So overall I would say it's about 11' 8" wide.
And with the screen so big I have to put my projector way, way back for it to project big enough to fill the screen. I'm still in the process of mounting my project (JVC RS40) but I did get a chance to watch Despicable Me last night. It looks great.
The box was missing the remote, the IR receiver, and a trigger cable. I called Monoprice and they issued an RMA... for the entire box. I told them it doesn't make sense to send a 12.5", 200lb box when all I need is 3 items but they told me to just take what I need and send it back. What?! lol I'm trying to contact their RMA department to resolve it.
post #265 of 573
Screen arrived today. When you see the size of the box, it is not too hard to see why they charge $135 to ship it across the country. That does not seem outrageous.
post #266 of 573
I am usually pretty good at following technical drawings, but I am having a tough time figuring out how the two plastic pieces of the masking mechanism are intended to lock together. Can anyone explain? I am afraid of breaking the plastic and so I do not want to force anything.

EDIT: Duh! Nevermind. I finally figured out that the plastic pieces in the top and bottom frame are only there for shipping and get removed for assembly.
.
LL
LL
post #267 of 573
They insert into the mask. You have to insert them before tightening everything down or you end up building it twice. Just like Nathan and I did!
post #268 of 573
Yessir. You are correct. Just for the benefit of the next person assembling one of these. The piece marked in the photo below (there are 4 of them total) gets removed before assembly. They have a sticker on them telling you this, but you cannot see the sticker until AFTER they have been removed! LOL.

BTW - I am thinking it might be wise to hold onto these in case one of the ones in the side bar should ever break - good to have a replacement.

.
LL
post #269 of 573
Ready to hang. Do wear safety glasses when attaching the springs that tension the screen. I had one pop off while I was adjusting the bar and it shot clear across the room. It could do some serious eyeball damage. There are some mild creases, etc in the screen, but hopefully they should come out under tension.

.

Attachment 230071
LL
post #270 of 573
Quote:
Originally Posted by slybarman View Post

Ready to hang.

About time!
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Screens
AVS › AVS Forum › Display Devices › Screens › New ranges of Monoprice screens seem to be coming soon