AVS › AVS Forum › 3D Central › 3D Tech Talk › Official Monster Vision Max 3D Thread
New Posts  All Forums:Forum Nav:

Official Monster Vision Max 3D Thread - Page 22

post #631 of 978
4/8/12 at 2:50pm
Quote:
Originally Posted by zeedub View Post

Is the 3dfury still outputting a 3d image on the screen. I am using the monstervision with curtpalme firmware on the 3dfury with great results.

I think so, that was my plan to but I updated the emitter while it was connected to the fury via the sync cable. Since then not one of my emitters will connect
I ran out of time but will try latter.
Reply
Reply

Gear mentioned in this thread:

post #632 of 978
4/8/12 at 6:38pm
Quote:
Originally Posted by trans_lux View Post


I think so, that was my plan to but I updated the emitter while it was connected to the fury via the sync cable. Since then not one of my emitters will connect
I ran out of time but will try latter.

The glasses may need to be paired again with the emitter. Have you done a factory reset of the glasses?
Reply
Reply
post #633 of 978
4/8/12 at 7:43pm
Quote:
Originally Posted by HokeySmoke View Post

The glasses may need to be paired again with the emitter. Have you done a factory reset of the glasses?

I can't get the emitters to sync up to the fury, the red lights just keep scanning back and fourth.
I'm sure something happened to the fury when I updated the emitter as it was attached via the sync cable. It also shows up as a device in device manager.
Anyone have the 3d fury firmware they could send me?
I can't get the fury guys to give it.
Reply
Reply
post #634 of 978
4/8/12 at 7:53pm
How do these glasses compare to the 3active?
Or the newer Panasonic??
Reply
Reply
post #635 of 978
4/9/12 at 7:42am
Quote:
Originally Posted by saltysteven View Post

How do these glasses compare to the 3active?
Or the newer Panasonic??

From what I see both are specific to particular manufactures displays.
The monsters combo-glasses & emitter-are a really nice combo. Lots of adjustments in the emitter. This is the key element for me. All the other systems I have used that are IR relied on settings in the displays. I'm using them with a 3dfury and a display that is not natively 3D ready and thus has no adjustments.
Now if I can just get my 3dfury to work again...
Reply
Reply
post #636 of 978
4/9/12 at 8:09am
Have you posted in the hdfury forum. They seem pretty quick to respond and help over there.
Reply
Reply
post #637 of 978
4/9/12 at 8:19am
Quote:
Originally Posted by trans_lux View Post

From what I see both are specific to particular manufactures displays.
The monsters combo-glasses & emitter-are a really nice combo. Lots of adjustments in the emitter. This is the key element for me. All the other systems I have used that are IR relied on settings in the displays. I'm using them with a 3dfury and a display that is not natively 3D ready and thus has no adjustments.
Now if I can just get my 3dfury to work again...

Does the emitter come with the monster vision glasses through Amazon for $72???
Reply
Reply
post #638 of 978
4/9/12 at 9:43am
Thread Starter 
Quote:
Originally Posted by saltysteven View Post


Does the emitter come with the monster vision glasses through Amazon for $72???

Yes it does. I just got a second pair. Great value!
Reply
Reply
post #639 of 978
4/9/12 at 9:53am
Quote:
Originally Posted by Vampyro View Post


Yes it does. I just got a second pair. Great value!

Great thanks!! Just ordered two!
What should I know before hand.?
Do they have to be tuned and is it difficult?
Reply
Reply
post #640 of 978
4/9/12 at 5:34pm
Quote:
Originally Posted by zeedub View Post

Have you posted in the hdfury forum. They seem pretty quick to respond and help over there.

Yes still no resolution. Waiting on firmware to try a reload.
I think the bottom line is don't update your emitter firmware while the sync cable is attached.
Reply
Reply
post #641 of 978
4/9/12 at 7:33pm
So one of my Optima glasses will not sync up. The other pair of Optima and Monster glasss sync up fine. These used to work fine as well. Any ideas?
Reply
Reply
post #642 of 978
4/10/12 at 6:39am
Quote:
Originally Posted by adidino View Post

So one of my Optima glasses will not sync up. The other pair of Optima and Monster glasss sync up fine. These used to work fine as well. Any ideas?

Try to recharge the Optima glasses and do a reset. Information is in the instruction manual.
Reply
Reply
post #643 of 978
4/10/12 at 7:24am
Quote:
Originally Posted by rwestley View Post

Try to recharge the Optima glasses and do a reset. Information is in the instruction manual.

I've already tried resetting. I'm thinking maybe re-pairing the glasses to the transmitter? I'll give that a shot and see.
Reply
Reply
post #644 of 978
4/13/12 at 3:34am
With a Sony front projector VPL-VW1000 I can't get the Monster glasses to work. They keep searching for the 3d IR signal. My sony glasses work fine. I have tried placing the monster ir receiver facing screen, PJ, etc. w/o results. Do they work w/o the optional Sony IR extender-transmitter? Do I have a defective pair or is there some trick to getting them to sync?

Thanks,
Dave
Reply
Reply
post #645 of 978
4/13/12 at 6:18am
^ How far apart is the Sony IR Emitter and where is it located? Make sure the lights are off when you try it because lights in the room interfere.
Reply
Reply
post #646 of 978
4/13/12 at 6:42am
Quote:
Originally Posted by LVS View Post

^ How far apart is the Sony IR Emitter and where is it located? Make sure the lights are off when you try it because lights in the room interfere.

I've tried hanging the IR receiver on the PJ so it is inches and aklso facing it towards the screen but lights were on very low. I can try again with all lights off tonight.
Reply
Reply
post #647 of 978
4/14/12 at 3:17am
As usual, user error. I did not have the sensor cable pushed in quite far enough. All is well.
Reply
Reply
post #648 of 978
4/14/12 at 3:42am
Quote:
Originally Posted by DaveN View Post

As usual, user error. I did not have the sensor cable pushed in quite far enough. All is well.

awesome.
Reply
Reply
post #649 of 978
4/17/12 at 10:53am
Quote:
Originally Posted by trans_lux View Post

So everything was working great I even was making progress on reducing flicker.
Then I decided to update to the Curt Palme listed firmware for the emitter to make polarity switching easier. Now the emitters will not sync with the 3Dfury.
I reverted firmware back to the Monster still no luck, took a new one and fresh cable out of the box and still no luck.
The only thing I can think of is that I did something to the 3DFury when I did the update as the emitter was connected to sync port. I can't imagine it back feed something but hey anything is possible.
Now all the emitters do is have the red LED's scanning back and forth.
No HUGO for the family on Easter
Any ideas?


What settings were you working with that helped reduce the flicker? I have an Infocus X10 running with the 3DFury, and I am about to work on reducing the flicker. Were you working with just the duty cycle settings or with delay as well? Please let me know. Thanks in advance.
Reply
Reply
post #650 of 978
4/19/12 at 7:03am
I have a Sony VW95ES. Are an emitter and the connection necessary? because VW95ES with Built-in Transmitter.
Reply
Reply
post #651 of 978
4/19/12 at 7:29am
Quote:
Originally Posted by trenchtownrock View Post

I have a Sony VW95ES. Are an emitter and the connection necessary? because VW95ES with Built-in Transmitter.

No.
Reply
Reply
post #652 of 978
4/19/12 at 7:36am
Do I only put on glasses?
Reply
Reply
post #653 of 978
4/19/12 at 7:50am
I have 4 pairs of these for my sony projector. I find that they DO NOT hold a charge. If they are turned off for a couple of weeks, when i try to use them, they are dead even after a full charge! not just one, but all of them. I have tried using different chargers and everything but the battery life is awful. Am i the only one with this problem?
Reply
Reply
post #654 of 978
4/19/12 at 8:53am
Thread Starter 
Quote:
Originally Posted by whitetrash66 View Post

I have 4 pairs of these for my sony projector. I find that they DO NOT hold a charge. If they are turned off for a couple of weeks, when i try to use them, they are dead even after a full charge! not just one, but all of them. I have tried using different chargers and everything but the battery life is awful. Am i the only one with this problem?

I think a couple of weeks with no power is reasonable. I noticed this also. The glasses will last a long time if used consistently. I would not worry about it
Reply
Reply
post #655 of 978
4/21/12 at 7:10pm
Hi All,

Here's an inexpensive solution for anyone experiencing reflection problems - Bat Vision!

http://www.avsforum.com/avs-vb/showt...1#post21935918
Reply
Reply
post #656 of 978
4/28/12 at 12:38pm
So I have a Panasonic TC-P65ST30

Are the Monster Cable Glasses still the best glasses to buy for a Active shutter Plasma?

Are they still offering a better picture?

thanks for the help!
Reply
Reply
post #657 of 978
4/28/12 at 2:51pm
This won't work if I have an acer 5360 dlp projector and I want to use with 3d vision (I have 3d vision emitter) correct?
Reply
Reply
post #658 of 978
4/28/12 at 5:54pm
Hi guys, before I jump into getting these glasses, and a 3dfury, can anyone tell me if there is any flicker at all? I am pairing it with an Epson 8350 pjay and it does 60hz. thanks for any replies
Reply
Reply
post #659 of 978
4/29/12 at 8:10pm
hi. u guys know how to reset / default the setting for the emitter. i want to reset the emittier to orginal setting. but i dont know how do i do that?

please help me.

i got hd33 projector.
Reply
Reply
post #660 of 978
4/29/12 at 10:52pm
Quote:
Originally Posted by audionewer View Post

hi. u guys know how to reset / default the setting for the emitter. i want to reset the emittier to orginal setting. but i dont know how do i do that?

please help me.

i got hd33 projector.

Read the manual http://www.monstercable.com/lit/Max_3D_manual.pdf

sec 2.1 Page 11 explains it.

Monster is selling the glasses and emitter for $59.95 now!!!!!
Reply
Reply
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: 3D Tech Talk

Gear mentioned in this thread:

AVS › AVS Forum › 3D Central › 3D Tech Talk › Official Monster Vision Max 3D Thread