Question on setting up crown on ypao - AVS Forum | Home Theater Discussions And Reviews
Forum Jump: 
 1Likes
  • 1 Post By johnson636
 
Thread Tools
post #1 of 6 Old 06-21-2019, 08:32 PM - Thread Starter
Member
 
Join Date: May 2018
Posts: 78
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 71 Post(s)
Liked: 6
Question on setting up crown on ypao

I'm almost done with my subs and most likely will be setting them up tonight, I'm just going by memory of browsing the forums a long time ago but I turn the knobs all the way up on the crown xls 2502 when I run ypao right?
valleyslim is offline  
Sponsored Links
Advertisement
 
post #2 of 6 Old 06-22-2019, 07:04 AM
AVS Forum Special Member
 
johnson636's Avatar
 
Join Date: Jan 2006
Location: Somewhere in the Outer Rim
Posts: 2,363
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 1150 Post(s)
Liked: 679
I don't know about anyone else, but I can't understand what you're trying to say Your words are garbled up.
stegen likes this.

Automation: Alexa- Harmony Hub- Wemo Dimmer Switch- Wemo Smart Plug BatCave: SY Triple Black
Video Image: JVC RS500- Sony UBP-800X- Chromecast- 125" wide 16x9 white over black spandex screen
Audio: 5.2.4 Marantz SR7011- (LCR) Stage Right 15" PA- (Surrounds) (4) BIC FH6-LCR- (Atmos) (4) Dayton Audio B652 6-1/2-Inch- (Subs)2 23ishcuft ported HS24s 14-15Hz tune- 4 MOFO 15s in 2 dual ported cabs 17Hz tune- FP20000Q- 2 Sanway FP10000Q- Crown XLS1500- . To be continued...
johnson636 is online now  
post #3 of 6 Old 06-22-2019, 07:09 AM
Member
 
nbk13nw's Avatar
 
Join Date: Dec 2004
Location: Williamsburg, Virginia USA
Posts: 179
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 73 Post(s)
Liked: 43
Start around the 11 or 12 oclock position on the crown. See what levels rhe AVR sets the subs. Aim for a level around -9 to -3. If the level is set low then turn up on the crown if needed or run the level on the AVR up to maybe -3 or so. Set it to where you like it, but personally i would not go above -3 on the AVR, adjust the crown amp to bring it up a bit to your preference

Onkyo TX RZ830, Chane 3600, AudioSource AMP100VS, XBox One X, Samsung UBD-K8500, NVIDIA Shield, D-Link 16-Port Gigabit Switch, Caavo, Control Center, 2 x KEF Q900's Mains, 1 x KEF Q650C Center, 4 x KEF Q100's Surrounds, 4 x RSL C34E's ATMOS, 4 x Chane SBE-118's
nbk13nw is online now  
Sponsored Links
Advertisement
 
post #4 of 6 Old 06-24-2019, 12:30 PM
Member
 
Join Date: Dec 2017
Location: Hudsonville, MI
Posts: 189
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 87 Post(s)
Liked: 91
Quote:
Originally Posted by johnson636 View Post
I don't know about anyone else, but I can't understand what you're trying to say Your words are garbled up.
As you're reading it, replace each s with an s.

--
Epson 2030 - Denon X1300W - Eosone RSF 1000 - Eosone RSC 300 - Eosone RSF 600 - Micca M-8C for ATMOS - 2 @ VBSS End Tables
DIY 110" AT Screen
jevchance is offline  
post #5 of 6 Old 06-24-2019, 12:33 PM
Member
 
RGrizzzz's Avatar
 
Join Date: Nov 2004
Location: Royersford, PA 19468
Posts: 51
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 29 Post(s)
Liked: 17
Quote:
Originally Posted by johnson636 View Post
I don't know about anyone else, but I can't understand what you're trying to say Your words are garbled up.
Newbie question. Why would you want the YPAO adjustment down in the -9 to -3 range? I'd think you'd want it as close to 0 as possible, so you have the most flexibility out of the knobs on your sub's amp.

Ron
RGrizzzz is offline  
post #6 of 6 Old 06-24-2019, 12:42 PM
Member
 
Join Date: Dec 2017
Location: Hudsonville, MI
Posts: 189
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 87 Post(s)
Liked: 91
Quote:
Originally Posted by RGrizzzz View Post
Newbie question. Why would you want the YPAO adjustment down in the -9 to -3 range? I'd think you'd want it as close to 0 as possible, so you have the most flexibility out of the knobs on your sub's amp.

Ron
So you don't clip the input on the Crown.

--
Epson 2030 - Denon X1300W - Eosone RSF 1000 - Eosone RSC 300 - Eosone RSF 600 - Micca M-8C for ATMOS - 2 @ VBSS End Tables
DIY 110" AT Screen
jevchance is offline  
Sponsored Links
Advertisement
 
Reply DIY Speakers and Subs

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page


Forum Jump: 

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off