Ushio NSHA250JK Bare Bulbs for JVC PK-L2615U - AVS Forum | Home Theater Discussions And Reviews
Forum Jump: 
 7Likes
Reply
 
Thread Tools
post #1 of 32 Old 05-30-2019, 12:07 PM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Ushio NSHA250JK Bare Bulbs for JVC PK-L2615U Projector Lamp

Note: I previously posted in the Classified section but apparently the Dealer Specials is more appropriate, according to the forum rules.
To avoid spurious notifications from being generated, please contact me by PM if you're interested, instead of replying to this thread.

FS: Ushio NSHA250JK Bulb for JVC PK-L2615U (RS400/RS500/RS600 etc)
I'm selling brand new Ushio NSHA250JK 265W bare bulbs. These can be installed in the JVC PL-L2615U/L2615UP lamp housing which is used in all recent JVC projectors (DLA-RS-400, RS-420, RS-440, RS-500, RS-520, RS-540, RS-600, RS-620, RS-640, X550, X750, X950 etc). Apparently even the new native 4K models use the same bulb, in a different housing (PK-L2618U).

Note that this is the 265W version of the Ushio lamp; older JVC projectors use 220W or 230W versions.

The cost is $120 USD plus $15 tracked shipping to US or Canada. Item will be shipped from Canada.

Installation instructions: It's relative easy to install the bulb into an existing housing. The only tools required are a Philips screwdriver and a pair of tweezers.

It's best to work with the lamp in the orientation shown in the picture once the 4 retaining screws are removed, as otherwise some parts may fall out.

To remove the old bulb:
- Remove screw 1 and the metal bracket that it holds. This is not strictly necessary but gives more ready access to the following steps.
- Remove the two screws 2 that hold the wires to the bulb terminals. Remember which wire goes where.
EDIT (Courtesy of forum member Dreamliner): There is a small spring that is held in place by the power connector, see the last attachment Power_Connector_Spring.jpg. If it falls out, please make sure you re-insert it before putting the power connector in place.
- Remove the four screws 3 (two shown in picture, two more at the back) that hold the brackets clamping the lamp to the housing. Lift up the four brackets, remembering the order. Lift up the bulb. There are more brackets underneath; do not remove those.

To install the new bulb, reverse these steps. Make sure when inserting the brackets, the little alignment pin poke through the hole. Also make sure all brackets are resting flush against the plastic housing, before tightening the screws. If necessary, reseat the lamp so that the brackets rest flush. Make sure the screws are snug but do not over-tighten them.
Attached Thumbnails
Click image for larger version

Name:	USH1.jpg
Views:	131
Size:	253.6 KB
ID:	2573642   Click image for larger version

Name:	USH2.jpg
Views:	143
Size:	749.6 KB
ID:	2573644   Click image for larger version

Name:	USH3.jpg
Views:	133
Size:	288.3 KB
ID:	2573646   Click image for larger version

Name:	USH4.jpg
Views:	124
Size:	217.1 KB
ID:	2573648   Click image for larger version

Name:	USH5.jpg
Views:	131
Size:	280.7 KB
ID:	2573650  

Click image for larger version

Name:	Power_Connector_Spring.jpg
Views:	31
Size:	611.9 KB
ID:	2621888  

Last edited by Dominic Chan; 10-04-2019 at 05:39 AM.
Dominic Chan is online now  
Sponsored Links
Advertisement
 
post #2 of 32 Old 06-15-2019, 09:33 PM
JJ7
Senior Member
 
JJ7's Avatar
 
Join Date: Nov 2007
Posts: 497
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 170 Post(s)
Liked: 104
I picked up a replacement bulb from Dominic and am very happy with it. My projector is now back to full brightness. And the procedure to install the bare bulb is not terribly challenging.
mtbdudex likes this.
JJ7 is offline  
post #3 of 32 Old 08-12-2019, 08:55 AM
AVS Forum Special Member
 
mtbdudex's Avatar
 
Join Date: May 2007
Location: SE Michigan
Posts: 6,830
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked: 1532
I have the RS400, besides bare bulbs you sell the full replacement? Is so how much?


Sent from my iPhone using Tapatalk
mtbdudex is offline  
Sponsored Links
Advertisement
 
post #4 of 32 Old 08-12-2019, 09:13 AM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by mtbdudex View Post
I have the RS400, besides bare bulbs you sell the full replacement? Is so how much?
No sorry. I only have the bare bulbs.
Dominic Chan is online now  
post #5 of 32 Old 08-12-2019, 12:08 PM
AVS Forum Special Member
 
mtbdudex's Avatar
 
Join Date: May 2007
Location: SE Michigan
Posts: 6,830
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 83 Post(s)
Liked: 1532
Quote:
Originally Posted by Dominic Chan View Post
No sorry. I only have the bare bulbs.


So I typically like to always have a back-up. Now if I buy the bare bulb and install that, then my backup is the 2,000 hours or so used bulb. Upon careful removal that should be still usable correct?


Sent from my iPhone using Tapatalk
mtbdudex is offline  
post #6 of 32 Old 08-12-2019, 12:46 PM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by mtbdudex View Post
So I typically like to always have a back-up. Now if I buy the bare bulb and install that, then my backup is the 2,000 hours or so used bulb. Upon careful removal that should be still usable correct?


Sent from my iPhone using Tapatalk
Yes, you can keep the current bulb as back-up.
Dominic Chan is online now  
post #7 of 32 Old 08-15-2019, 12:00 PM
Newbie
 
livermore larry's Avatar
 
Join Date: May 2005
Posts: 14
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked: 10
I’m interested in a bulb for a JVC RS 400. How do I proceed?
livermore larry is offline  
post #8 of 32 Old 08-15-2019, 12:30 PM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by livermore larry View Post
I’m interested in a bulb for a JVC RS 400. How do I proceed?
If you provide your email (by PM if you prefer) I will send you a PayPal invoice. They are currently out of stock; next shipment about 3 weeks.
Dominic Chan is online now  
post #9 of 32 Old 08-15-2019, 12:54 PM
Newbie
 
livermore larry's Avatar
 
Join Date: May 2005
Posts: 14
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked: 10
My email is [email protected]
livermore larry is offline  
post #10 of 32 Old 08-16-2019, 05:17 AM
Member
 
estabanj's Avatar
 
Join Date: Feb 2004
Location: Mountain View California
Posts: 27
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Liked: 14
Dominic has anyone used these in a NX 5/7/9 yet? Would the instructions be similar / the same?

Thanks Stephen
estabanj is offline  
post #11 of 32 Old 08-16-2019, 05:52 AM
AVS Forum Special Member
 
markmon1's Avatar
 
Join Date: Dec 2006
Posts: 6,218
Mentioned: 106 Post(s)
Tagged: 0 Thread(s)
Quoted: 5225 Post(s)
Liked: 3391
Quote:
Originally Posted by estabanj View Post
Dominic has anyone used these in a NX 5/7/9 yet? Would the instructions be similar / the same?

Thanks Stephen
Its the same bulb. The housing will be a little different but that shouldn't matter much.

Video: JVC RS4500 135" screen in pure black room no light, htpc nvidia 1080ti.
Audio: Anthem mrx720 running 7.1.4, McIntosh MC-303, MC-152, B&W 802d3 LR, B&W HTM1D3 center, B&W 805d3 surround, B&W 702S2 rear, B&W 706s2 x 4 shelf mounted for atmos, 2 sub arrays both infinite baffle: 4x15 fi audio running on behringer ep4000 + 4x12 fi audio running on 2nd ep4000.
markmon1 is offline  
post #12 of 32 Old 08-17-2019, 06:28 PM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by estabanj View Post
Dominic has anyone used these in a NX 5/7/9 yet? Would the instructions be similar / the same?

Thanks Stephen
Someone did buy one for the NX9, but as a spare so he won't be using it for quite a while.
Dominic Chan is online now  
post #13 of 32 Old 08-18-2019, 07:54 AM
Member
 
estabanj's Avatar
 
Join Date: Feb 2004
Location: Mountain View California
Posts: 27
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Liked: 14
Quote:
Originally Posted by Dominic Chan View Post
Someone did buy one for the NX9, but as a spare so he won't be using it for quite a while.
Yeah that is exactly what I am looking to do. I will PM you my email.

Cheers
estabanj is offline  
post #14 of 32 Old 08-22-2019, 02:14 AM
Newbie
 
mr richie's Avatar
 
Join Date: Aug 2013
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked: 0
Hi everyone, my name is Riccardo and I write from Italy, I ask Dominic to be contacted on PM, I don't have enough posts on this forum, for the purpose of buying jvc rs400 bulb.
Many congratulations to all for the good of this community.
P.S: I apologize for my English, but I'm using the google translator.
mr richie is offline  
post #15 of 32 Old 08-22-2019, 05:05 AM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by mr richie View Post
Hi everyone, my name is Riccardo and I write from Italy, I ask Dominic to be contacted on PM, I don't have enough posts on this forum, for the purpose of buying jvc rs400 bulb.
Many congratulations to all for the good of this community.
P.S: I apologize for my English, but I'm using the google translator.
I have sent you a PM with my email address.
Dominic Chan is online now  
post #16 of 32 Old 08-22-2019, 10:53 AM
Newbie
 
mr richie's Avatar
 
Join Date: Aug 2013
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked: 0
Thank you so much.
mr richie is offline  
post #17 of 32 Old 09-10-2019, 01:25 PM
Member
 
estabanj's Avatar
 
Join Date: Feb 2004
Location: Mountain View California
Posts: 27
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Liked: 14
Quote:
Originally Posted by mr richie View Post
Thank you so much.
Dominic,

Did you get my PM?

Thanks
estabanj is offline  
post #18 of 32 Old 09-10-2019, 01:27 PM
Member
 
estabanj's Avatar
 
Join Date: Feb 2004
Location: Mountain View California
Posts: 27
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 8 Post(s)
Liked: 14
Quote:
Originally Posted by Dominic Chan View Post
Someone did buy one for the NX9, but as a spare so he won't be using it for quite a while.
Hi Dominic

Did you get my PM?

Thanks Stephen
estabanj is offline  
post #19 of 32 Old 09-10-2019, 01:35 PM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by estabanj View Post
Hi Dominic

Did you get my PM?

Thanks Stephen
Just replied.
Dominic Chan is online now  
post #20 of 32 Old 09-24-2019, 04:13 PM
Newbie
 
Join Date: Jan 2017
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Liked: 0
Hello Dominic, I would like to purchase a Ushio bulb for JVC RS440. Please contact me at "[email protected]"

Thanks
N0 Substitute is offline  
post #21 of 32 Old 09-29-2019, 08:56 AM
Newbie
 
jonmula's Avatar
 
Join Date: Mar 2013
Location: Myrtle Beach, South Carolina
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Liked: 3
Just installed one of these bulbs in my RS400. Brighter then I remember the unit being when brand new! Thanks, Dominic!
Dominic Chan likes this.
jonmula is offline  
post #22 of 32 Old 10-02-2019, 04:30 PM
AVS Forum Special Member
 
alebonau's Avatar
 
Join Date: Jan 2006
Location: Land of Contentment :)
Posts: 4,776
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 1889 Post(s)
Liked: 1290
hi dominic do you ship outside of canada and the us ?

"Technology is a drug. We can't get enough of it."


Welcome to my lounge room :)
alebonau is offline  
post #23 of 32 Old 10-02-2019, 05:32 PM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by alebonau View Post
hi dominic do you ship outside of canada and the us ?
I can ship by Small Packet International Air to Australia, but it does not provide tracking. Tracked shipping is expensive - $35 USD extra.
alebonau likes this.

Last edited by Dominic Chan; 10-02-2019 at 05:35 PM.
Dominic Chan is online now  
post #24 of 32 Old 10-02-2019, 06:49 PM
AVS Forum Special Member
 
alebonau's Avatar
 
Join Date: Jan 2006
Location: Land of Contentment :)
Posts: 4,776
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 1889 Post(s)
Liked: 1290
Quote:
Originally Posted by Dominic Chan View Post
I can ship by Small Packet International Air to Australia, but it does not provide tracking. Tracked shipping is expensive - $35 USD extra.
thanks dominic. I'll pass on to folks this way... you never know the interest

"Technology is a drug. We can't get enough of it."


Welcome to my lounge room :)
alebonau is offline  
post #25 of 32 Old 10-03-2019, 05:11 AM
Newbie
 
Darkknighttx's Avatar
 
Join Date: Oct 2019
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Liked: 0
Hi Dominic, very interested in the lamp PK-L2615U for my RS400U. How long is the warranty?

Thank you sincerely.
Darkknighttx is offline  
post #26 of 32 Old 10-03-2019, 10:25 AM
Newbie
 
Join Date: Oct 2019
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Liked: 0
just created my account, so it looks like I don't have the post count to send PMs yet, so I guess I'll post directly to the threat.

I'm just wondering how much in CAD would you charge for these, and would I be able to pick one up from you directly?

I live in Oakville, so I shouldn't be too far away.

Thanks!
Iceman888 is offline  
post #27 of 32 Old 10-03-2019, 10:44 AM
Newbie
 
Darkknighttx's Avatar
 
Join Date: Oct 2019
Posts: 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Liked: 0
I sent you a PM with my email. I really want to buy one lamp but, I'm considering buying two to have a new spare. Looking forward to your reply 😁👍
Darkknighttx is offline  
post #28 of 32 Old 10-03-2019, 01:14 PM - Thread Starter
AVS Forum Special Member
 
Join Date: Dec 2014
Location: Mississauga, ON, Canada
Posts: 6,936
Mentioned: 129 Post(s)
Tagged: 0 Thread(s)
Quoted: 4876 Post(s)
Liked: 1840
Quote:
Originally Posted by Darkknighttx View Post
I sent you a PM with my email. I really want to buy one lamp but, I'm considering buying two to have a new spare. Looking forward to your reply 😁👍
Replied by PM.
Dominic Chan is online now  
post #29 of 32 Old 10-04-2019, 03:40 AM
Advanced Member
 
jasonDono's Avatar
 
Join Date: Jul 2003
Location: Brooklyn, NY
Posts: 695
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Liked: 10
Can you please stop posting this every day? I’m going to have to unsubscribe from this forum. Thank you.
jasonDono is offline  
post #30 of 32 Old 10-04-2019, 03:48 AM
AVS Forum Special Member
 
lizrussspike's Avatar
 
Join Date: May 2008
Location: Parkview, IA
Posts: 3,058
Mentioned: 32 Post(s)
Tagged: 0 Thread(s)
Quoted: 1216 Post(s)
Liked: 1822
@jasonDono , you can change the way you are notified. If not happy with what @Dominic Chan is doing, then simply unsubscribe, I, like others rely on updates to forums, so we are in the know.....
lizrussspike is offline  
Sponsored Links
Advertisement
 
Reply Dealer Specials

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page


Forum Jump: 

Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off