AVS Forum banner
behringer europower ep4000 professional amplifier
1-20 of 36 Results
  1. DIY Speakers and Subs
    Can someone that has any particular experience with this driver tell me how much power I should feed these bad boys? http://store.ficaraudio.com/ib318/ I was thinking somewhere in the realm of 500 watts per driver. Is this too much or too little?
  2. DIY Speakers and Subs
    couple questions I am looking at upgrading my Keiga 52100 plate amp to a EP4000 amp or the sorts. I am running Passive radiator setups in my builds. My question is that I read the HPF is defeatable on the amp. If this correct and is it as easy a switch. I would like to have it set around 15hz...
  3. Receivers, Amps, and Processors
    couple questions I am looking at upgrading my Keiga 52100 plate amp to a EP4000 amp or the sorts. I am running Passive radiator setups in my builds. My question is that I read the HPF is defeatable on the amp. If this correct and is it as easy a switch. I would like to have it set around 15hz...
  4. DIY Speakers and Subs
    I need a power amp to drive two pairs of 175w outdoor speakers with some long cable runs. These speakers are nominal 8 Ohms and will be used for the same stereo content so could be wired in parallel for a 2ch Amp that can handle 4 Ohm loads I guess. I too don't really know but from what I've...
  5. Receivers, Amps, and Processors
    Long story short... I had dog-zilla roll through my area and she ripped out a channel from the back of the sub it was actively powering. So, each channel was running a different sub... Channel 2 (the one my dog ripped out) now basically says it's clipping constantly, red light sorta flickers...
  6. DIY Speakers and Subs
    I am confused by the switch settings to bridge my 2 behringer amps. On the EP2500 I have 3, 6,7,8 to the right and it seems to be fine with so signal coming through the other channel since its in stereo with parallel off. If i turn parallel on it clips. On the EP4000 the same settings give...
  7. DIY Speakers and Subs
    Hey, Starting a new build, and also new to DIY sub building. I plan to build 2 sealed 15's. I have 1 Dayton Audio 15" Ultimax/flat pack and a ep4000 on the way. I will order another Ultimax kit down the road a bit. Current parts list: Dayton Audio 15" Ultimax Subwoofer and Cabinet Package...
  8. Receivers, Amps, and Processors
     Hello everyone, I am new here. I will introduce myself. I am an advent audio enthusiast. Loved audio since  i was a small child. Always looking for ways to improve my home theater! I have run into a snag that I cannot get myself out of. I will explain my set up first: 5.1 Surround, custom...
  9. Receivers, Amps, and Processors
    Recently returned here - got another q for you guys. Going to be doing a 7.1 HT. I'm not overly concerned about the amps used for my surround channels. I have a good multi-channel now. I'm more focused on getting something decent for my two fronts (maybe for the center). I'm going to be driving...
  10. DIY Speakers and Subs
    I have read a LOT of threads about the iNukes and may have missed something, but I cannot find a definitive answer as to the roll off of them. I am debating the NU3000DSP or another EP4000 for my buttkickers. Obviously I want the least amount of roll off and know the EP4000 has been measured to...
  11. DIY Speakers and Subs
    Hey everyone, Just thought I'd let you know about a deal on the Behringer EP4000. From what I've read, it used to be $300 quite often but seems to stick around $379 now. Anyways, I found it listed on eBay from Unique Squared for $299 with a "Make Offer" option. I looked around and found some...
  12. Receivers, Amps, and Processors
    I posted a similar question in the subwoofer forum without any luck, so I'm trying over here. I currently have 6 buttkickers in my media room. 3 are in the series and the other 3 are in series and then I hooked the 2 sets together in parellel. I had a behringer ep4000 amp for the last 2...
  13. Audio Gear
    As stated in title, EP4000 with 1 channel that works. The first channel works perfectly and has driven my dual opposed MFW-15 DIY sub perfectly (which I am also selling in another thread). It also has the fan mod completed, which was completed by me. I'm not sure what's wrong with the 2nd...
  14. DIY Speakers and Subs
    Need some advice here, first DIY project I've ordered a Mach 5 uxl-18, should get it by the end of the week. Need a small box so i'm going sealed. 3.5ft3 should give me good performances according to Winisd Pro. I'm trying to decide between the Behringer ep2000 bridged mono at 2000w/4ohms...
  15. Audio Gear
    I have one EP4000 amp for sale. it is in like new condition. never abused. used in a smoke free, pet free, kid free, well ventilated environment for sub duty in my home theater. i do not have the box for this so local pickup only from Canton, MI 48187
  16. DIY Speakers and Subs
    So after several months of planning...and waiting, I've finally started building the the box for a UXL-18 in a 7.6 cubic foot box tuned to 15hz. The plan: Dimensions: The exterior dimensions are 25h x 25w x 30d made of 3/4 MDF with plywood for the speaker mount. Ports It will use four 3"...
  17. DIY Speakers and Subs
    I finished building my sub combo pack from PE yesterday. I hooked up the behringer ep4000 to 1 sub to test it. The sub was very weak, it played a little, but it was weak even with the gain turned up. I plugged the same input into my BIC PL200 and it sounded strong. I don't know what is...
  18. DIY Speakers and Subs
    Hey guys - I'd appreciate some input. I think I might be making some things more complicated and expensive than it needs to be. I'm trying to spec a set of subs for my in-progress HT space. I'm still building - no riser or stage or soffits yet - no door either - but I want to get my sub system...
  19. DIY Speakers and Subs
    I been looking at DIY subs. I looked at building dual 18" subs and it came out to be less than $1300. Am I missing something?
  20. DIY Speakers and Subs
    I'm configuring the dip switches for my Behringer EP4000 AMP to use with my 2x 4cuft sealed boxes flat packs. Once i have done that i'm ready to test each speaker. I just want to be sure of my settings...... Amp: Bridged 1-10 off (Left) 2-9 on (Right) Channel 1 knob good up to 100%...
1-20 of 36 Results
Top