AVS Forum banner
crossover
1-20 of 54 Results
  1. Audio Theory, Setup, and Chat
    Looking for recommendations on my 5.2.2 front high configuration with Polk speakers and Onkyo amp crossover settings. I want full range and bass without blowing out the speakers. Amp Onkyo 797 - 5.2.2 bi-amp mode 100 watts/channel continuous, 220 w peak bi-amp. Center s35 - 90 mhz crossover...
  2. Speakers
    Hello, am new to forum and am looking for instructions to access crossover on M1si. I have seen and read about accessing the M3si crossover on inside side panel after removing woofer. But I think on the M1si you have to access it by removing bottom base plate and a second plate underneath the...
  3. DIY Speakers and Subs
    Hi everyone! I'm so excited to jump into my first ever build with a passive crossover! These are my drivers: https://www.parts-express.com/Dayton-Audio-DC28F-8-1-1-8-Silk-Dome-Tweeter-275-070 https://www.parts-express.com/Dayton-Audio-DS175-8-6-1-2-Designer-Series-Woofer-295-428 They are going...
  4. DIY Speakers and Subs
    Hello guys, I'm designing my own speakers for my home. I've chosen the following drivers and crossover: Hertz 1650.3. Both the tweeter and woofer are rated at 4 ohms each. I plan to pair them with my Denon pma600ne which supports 4 ohm speakers. Because these speakers are normally meant to be...
  5. DIY Speakers and Subs
    So here's the deal, i've got a set of old floor standing speakers, and 1 center speaker and a pair of floorstanding ones just laying around taking up space... since i really can't be bothered to sell these i recently started considering just removing the speaker elements from them and using them...
  6. Front Projectors Great Found Deals!
    New guy here i cant get good sound out of my setup. I did much resaerch and settled on the andrew jones 5.0 SP-PK52FS which included the tower front speakers (SP-FS52) i also have the matching pioneer atmos addons in front giving me 5.1.2. My receiver is the vsx-834. Its my first real home...
  7. Audio Gear
    Selling a MiniDSP DDRC-24 with Dirac and a remote, along with a calibrated UMIK-1 microphone. These are in like-new condition, as I have only used them for a couple of days. I bought them to run as a crossover so I could add a subwoofer to my active speakers. I've since decided to go another...
  8. Speakers
    Good day, my first post! WHY IT HAPPENED: I have a set of KEF C7's I use in my dorm at my university residence either at a really low volume (to study) or REALLY loud (special occasions party vibe...) In our home's living room they can't fill the room with deep bass (although being quite a...
  9. 2-Channel Audio
    Hey Everyone, I am looking for an answer to what i think is a very basic confusion about connecting sub-woofer/s to a stereo system. Either i have the understanding all wrong to this seemingly simple concept or i feel more people should have been asking this, because i looked all over and...
  10. DIY Speakers and Subs
    Like many my 'CS-G303's are ok. But the paper on the midranges is shot. I think this is a common issue with vintage-paper-cones. Especially this model. It looks like when you search on ebay for parts, you can't even find people selling ones that aren't 'worn'. I seem to remember people...
  11. Speakers
    I am starting to put together my first home theater and came across something I don't understand in some of the Klipsch center channel speaker specs. They are listing 2 crossover frequencies with only two speaker sizes in an enclosure, a woofer and a tweeter. For example: RC-64 III: 1,000 Hz &...
  12. Speakers
    Hello all, I'm not looking for sales advice or anything this is just confusing the hell out of me because I want to choose the best speaker for my system and I think there needs to be a source of information on the internet as to which of these speakers would be best for a sub/sat config. Here...
  13. Speakers
    Hi AVSForum Newbie here, hoping to get advice on repairing/upgrading the crossovers for a pair of KEF C20 type SP3053 speakers (100W 8 Ohm) which have been in the family for more than 30 years. One crossover is fine, the other crossover doesn't work at all (I tested the drivers by swapping the...
  14. Audio Theory, Setup, and Chat
    We all know the coveted HT rule: Set your speakers as small/limited range with a 80-100Hz crossover, even if you have tower speakers, spare your amp and speakers the extra work, and let your sub take care of the lows. Here's my thing...what do you tell the person who's a "purist" and only runs...
  15. Receivers, Amps, and Processors
    Before anyone says it, yes I did indeed look through the threads on AVS but there is just so much content to look through. I've had my setup for about a year now but recently I felt like it wasn't calibrated properly so I've gone back into the settings to put what is currently in the pictures...
  16. Audio Gear
    ** SOLD ** EDIT 7/4/2018: Price lowered again. Barely used, perfect condition MiniDSP 10x10 HD, purchase new in 2016. I will include both the 2x8 and 8x8 software "plug-in" files, required to configure the unit. This unit has an amazing amount of functionality, and very good sound. Asking...
  17. Speakers
    So I just got a new sub for my audio setup and it has a crossover setting. I understand that the crossover is the frequency at which the sub takes over but I'm not sure what it should be set to. My setup: Yamaha R-S202BL Receiver 2x Polk TSx 330T Tower Speakers Klipsch Reference R-8SW Subwoofer...
  18. Subwoofers, Bass, and Transducers
    Adding a subwoofer to a tube amp set Hello there. I have a little tube amp (Unison Simply Italy), and I want to add a Velodyne subwoofer to my stereo set. Unfortunately, the amp doesn't come with a dedicated out for LF: just the speaker outs. Up until now I had the sub hooked through the...
  19. Subwoofers, Bass, and Transducers
    Just got an Elac Debut S10 and I'm taking some measurements with my SPL meter to try and get the right crossover/level settings. I've noticed that the low pass filter knob (range 50 - 150Hz) never fully quiets sound above the knob's setting. That is to say that if play a 100Hz tone, and sweep...
  20. Subwoofers, Bass, and Transducers
    Does anyone have experience with Inline RCA form-factor high pass filters - like the FMOD Inline Crossovers from Harrison Labs? I want to keep deep bass frequencies from reaching the bookshelf/satellite main speakers.
1-20 of 54 Results
Top