AVS Forum banner
phono
1-12 of 12 Results
  1. Audio Gear
    Genuine (non-aftermarket) fully working condition Arcam Phono Board for MM/MC cartridges for the Arcam Alpha 9, Alpha 10 range of amplifiers. Extremely rare, hard to find in USA. This one I removed from my Alpha 10 Amplifier. This is a very high class phono board and is much cheaper than buying...
  2. Audio Theory, Setup, and Chat
    I had to move my turntable from the main rig. It stands by itself, separately, in an opposite corner. Naturally, I had to purchase a longer RCA cable(an AudioQuest Evergreen 8m) running from my Pro-Ject Phono Box DS+ to the preamp. That opened up possibilities for upgrading the other phono...
  3. Receivers, Amps, and Processors
    Greetings, New to AVSF. Tell what to buy or do I fix vintage Onkyo TX-37. I'm the original owner of the Onkyo TX-37. Bought it in high school with money from my first job. I've used her ever since as my only receiver. She still works but channels cut in and out and crackle (mostly right...
  4. Subwoofers, Bass, and Transducers
    Gents, Please help me out a bit. When I was doing my place, i put some standard speaker cables into the wall (looks like attached). Of course, I now facing an issue with my subwoofer connection. It should be connected by RCA plug. What is the best way to use it? Or it is all useless?
  5. Audio Gear
    Not available Long story short I am selling my week old(to me) XSP-1 G1. It works flawlessly aside from not working with my Integra 80.2 for bi-amping my mains the way integra recommends. Regardless, I deleted my old post and now have all my new speakers up and running. I would like to package...
  6. Receivers, Amps, and Processors
    Hello everyone, I have a vintage Pioneer receiver, and a new Audio Technica turntable. If I connect the turntable to the phono input on the receiver, then there is a horrible hum, like it needs to be grounded. The receiver does have a screw to connect a grounding wire, but the turntable is...
  7. 2-Channel Audio
    I recently got back into vinyl by purchasing a Pro-Ject Carbon DC with the Ortofon 2M Red cartridge. I'm enjoying the whole experience and am looking for my 1st upgrade, a phono preamp, to replace the Behringer PP400 I currently have. My budget is $250 max but under $150 would be great. I want...
  8. Audio Theory, Setup, and Chat
    Hello. Was wondering if I could get some advice on how to best add a volume control to my set up. What I have is a turntable running through a NAD phono preamp into a pair of powered studio monitors, so I have all pre and power amplification covered, but the only way for me to adjust the...
  9. Receivers, Amps, and Processors
    Hello everyone, I'm an audio newb who recently became fascinated with analog sound and equipment. I currently have a JVC JR S100 receiver (has a phono) that lines the sound from my turntable (Sony PS-T3) to my speakers. I am considering buying a separate preamp because I have heard the sound...
  10. Receivers, Amps, and Processors
    Hi, this is my first post. I need some help to pick a new receiver, but my requirements are so specific, that I can't seem to get any help at local audio stores. The main problem I am having is that I record a lot of music into my itunes from LPs and cassettes. I listen to a lot of obscure...
  11. 2-Channel Audio
    Receiver: Integra DTM-5.9 Current speakers: Yamaha NS-A836 I mainly use this setup for listening to vinyl. these speakers are great, but I'd like something a little less bulky and with brighter high-range sound. My budget is around $200/speaker Ideally looking for floor-standing speakers What...
  12. Receivers, Amps, and Processors
    I have a Marantz 2226B receiver and an Onkyo TX-SR508 receiver. Right now, whenever I want to play a record, I have to change the speakers from the Onkyo to the Marantz. I was wondering if there was a way to connect the Marantz to the Onkyo and just do direct audio since the Onkyo doesn't have a...
1-12 of 12 Results
Top