AVS Forum banner
yamaha rx v765bl 665 watt 7 channel home theater receiver
1-19 of 19 Results
  1. Receivers, Amps, and Processors
    I have the Yamaha RX-V765BL and a Roku connected via HDMI (to HDMI2) The Roku is set to 5.1 surround, but the receiver display shows PCM. I have tried to change the settings for HDMI2 but I can't get 5.1 surround. Any suggestions?
  2. Receivers, Amps, and Processors
    I have an HDMI connection to the receiver from a laptop and it works just fine. I want to send an analog audio signal to the receiver from the laptop headphones so that I can pick up that signal in Zone 2. So, I connected the laptop headphones to the AUX input. Here is the problem I am having...
  3. Receivers, Amps, and Processors
    Currently I am running my V765 in full-range stereo mode with pre-amp outs going to a Behringer A500 amp. No other speakers are connected, just using the front R/L preamp RCA outputs to go to the A500. My speakers are a Dayton Classic WMTMW (see my build thread). (also Panasonic Bluray...
  4. Receivers, Amps, and Processors
    Hi all, Hoping you can help, I have had this setup up for a couple of years now and have never really been happy with it, voices seem drowned by sound effects. I have recently set receiver to straight, and speakers to small and have seen an improvement. I have also read that I should set...
  5. Receivers, Amps, and Processors
     Hi all, hoping to get a bit of advise from you.   I have had the below setup for sometime but am now trying to get the best out of it, the main thing I was hoping to improve is the sound. when the sound effects kick in during a film the voices are quite difficult to hear.   Mains = no...
  6. Speakers
    Asked and got some advice on another forum, but as stubborn and inquisitive as I am, I'd like to have some more opinions and advice. 'upgrade' - to me also stands for hearing something different to what I have been used to for the past 7-8 years. My setup is more or less 99% Movies, it's...
  7. Receivers, Amps, and Processors
    Good day, A quick question for the pros out there. I have a Yamaha RX-V765 that I have been using as my Jukebox for about 6 years now. To explain: I have a pc that is running a Planar touchscreen with the TouchTone Audio System. Recently I have noticed that the display on the receiver...
  8. Receivers, Amps, and Processors
    I somehow misplaced my remote and am now stuck trying to find a way to set my speaker settings along with running the setup mic. I have the received setup on my old harmony but cant seem to find a way to scroll through settings once in the setup mode. Anyone have any tips on how I can set my...
  9. Receivers, Amps, and Processors
    As the subject says, I have a Yamaha RX-v765 receiver. I want to run an HDMI cable from my computer to display the video but want to use the Multi Channel input for the audio. Everything I read says that the Multi Channel Input can only be used with AV 1-6 which will only take component or...
  10. Digital Hi-End Projectors - $3,000+ USD MSRP
    Hi everyone. I recently got my RS45 installed and am very very happy with it. I have it hooked up to a Yamaha RX-V765 AVR and after enabling HDMI Control in the projector options, and also enabling it on the receiver, I observe than when the projector is turned off, it also turns off the...
  11. Receivers, Amps, and Processors
    DELETED
  12. Receivers, Amps, and Processors
    I have a question regarding Straight vs 2 Channel Stereo mode. Yamaha describes 2channel stereo mode as "Produces front stereo sound. This is standard playback mode". It is also the mode that will automatically bypass the DSP circuit when an analog sound source is selected as the input...
  13. Receivers, Amps, and Processors
    I have a question regarding Straight vs 2 Channel Stereo mode. Yamaha describes 2channel stereo mode as "Produces front stereo sound. This is standard playback mode". It is also the mode that will automatically bypass the DSP circuit when an analog sound source is selected as the input...
  14. Receivers, Amps, and Processors
    I've always been into mobile audio, I've had a Dynaudio, McIntosh & Nakamachi setup in my car for the last 8 years. Can't say the same for my home setup, I had a $300 all in one Sony Blu-ray system. Yesterday I picked up a used Klipsch F-3, S-2, C-2 and Sub-12 speakers. I also picked up a...
  15. Receivers, Amps, and Processors
    Thanks in advance for any suggestions. My Setup: Yamaha RX V-765 Polk Audio Speakers Monitor 70 x2 (front) Monitor 60 x2 (rear) CS20 x 1 (center) Monitor 40 x2 (surround) PSW10 x 2 (front and back subs) Also running an Epson 8100 projector, PS3, Xbox 360 and Directv HR24 DVR...
  16. Receivers, Amps, and Processors
    Hey there =) I've had my receiver since around march of last year. It's worked perfectly since I picked it up. I realized last night that I'd never used the microphone and the YPAO or whatever it's called, automatic setup. I ran the utility, it did it's thing and said it was all good. I...
  17. Receivers, Amps, and Processors
    I can't believe that there are countless pages in the Official Yamaha 665 Thread but there isn't one for the 765. I just unboxed my new 765 this week and love it! It replaced an RX-V740 that did not have HDMI, nor 7.1 capability. The things I love about the 765: The HDMI standby pass...
  18. Receivers, Amps, and Processors
    I recently upgraded from a Sony XBR2 to a Sony XBR9 and suddenly have trouble with HDMI switching on the RX-V765. When I turn on the XBR9, somehow the RX-V765 gets switched from HDM1 (DVR) to HDMI2 (PS3), even when it is in pass-through mode. I can turn on the 765, switch it back to HDMI1, and...
  19. Receivers, Amps, and Processors
    I recently purchased a Yamaha RX-V765 receiver to replace an older receiver with no HDMI or much of anything for that matter. Anyway, I was looking on Yamaha's website and noticed that there is a firmware upgrade for this receiver. I downloaded the WAV audio file, burned it to a cd as a CDDA...
1-19 of 19 Results
Top