I have an Elunevision Tab Tensioned Motorized screen with a Panasonic projector. I connected the remote trigger to a femal to male mono mini plug extension cable and plugged that into the projector. It works flawlessly. The projector has a built in delay that doesn't send the 'down' signal until it has warmed up, about 45 seconds or so. When shutting off it sends the 'up' signal immediately.
-
Get an exclusive sneak peek into our new project. >>> Click Here
Elunevision Tab Tensioned Motorized Screen Trigger Issue Help ?
Any one that have Elunevision Titan Tab Tensioned Motorize Screen and using the trigger function .
Can you please elaborate on it ,i have 120" motorized tab tension at home and trying to
mono jack from Panasonic Projector to it but no go , it's seem to go half way and in angle which don't make sense so prevent any problem i email elunevion from their website and the answer didn't make sense to me ( Connect is mini barrel connector ,id is 1.3mm,od is 3.5mm ) i have all sort of adapter 2.5 mm ,3.5mm kit stereo or mono none of them go thru just half way in .
Anyone one else having this issue.or any screen recommendation with 12V Trigger that work flawlessly ,i'm still under warranty can take it back if can use the function.
Thanks
Leonsmalto
Edmonton , AB
![]()
Any one that have Elunevision Titan Tab Tensioned Motorize Screen and using the trigger function .
Can you please elaborate on it ,i have 120" motorized tab tension at home and trying to
mono jack from Panasonic Projector to it but no go , it's seem to go half way and in angle which don't make sense so prevent any problem i email elunevion from their website and the answer didn't make sense to me ( Connect is mini barrel connector ,id is 1.3mm,od is 3.5mm ) i have all sort of adapter 2.5 mm ,3.5mm kit stereo or mono none of them go thru just half way in .
Anyone one else having this issue.or any screen recommendation with 12V Trigger that work flawlessly ,i'm still under warranty can take it back if can use the function.
Thanks
Leonsmalto
Edmonton , AB
1 - 5 of 5 Posts
I have 106" and trigger from them, doesnt work all the time, at times just goes up others the other way around. Gave up on it
![]()
just use remote which works all the time.
Having the same problems here...
I have a 106 Motorized Tension screen.
Thinking I had a dud for a 25ft 3.55mm cable, but now I read this thread and think otherwise!
I'm looking for any solutions and will likely call / email Elunevision to help resolve this. The whole idea of going this route was to have the WOW factor... I'm a little disappointed right now but I'm hoping for the best.
If anyone has any update please send me an updated thread or note.
Cheers,
RC
I have a 106 Motorized Tension screen.
Thinking I had a dud for a 25ft 3.55mm cable, but now I read this thread and think otherwise!
I'm looking for any solutions and will likely call / email Elunevision to help resolve this. The whole idea of going this route was to have the WOW factor... I'm a little disappointed right now but I'm hoping for the best.
If anyone has any update please send me an updated thread or note.
Cheers,
RC
Having the same problems here...
I have a 106 Motorized Tension screen.
Thinking I had a dud for a 25ft 3.55mm cable, but now I read this thread and think otherwise!
I'm looking for any solutions and will likely call / email Elunevision to help resolve this. The whole idea of going this route was to have the WOW factor... I'm a little disappointed right now but I'm hoping for the best.
If anyone has any update please send me an updated thread or note.
Cheers,
RC
I have a 106 Motorized Tension screen.
Thinking I had a dud for a 25ft 3.55mm cable, but now I read this thread and think otherwise!
I'm looking for any solutions and will likely call / email Elunevision to help resolve this. The whole idea of going this route was to have the WOW factor... I'm a little disappointed right now but I'm hoping for the best.
If anyone has any update please send me an updated thread or note.
Cheers,
RC
1 - 5 of 5 Posts
