AVS Forum banner

1281 - 1300 of 1314 Posts

·
Premium Member
Joined
·
4,155 Posts
DV with Atmos running on Rx a 3050
I notice that you are sending LLDV directly to the JVC. I assume you must be manually selecting a JVC HDR configured user mode to process the input. Otherwise the colors will not be correct with an SDR configured user mode.
 

·
Registered
Joined
·
208 Posts
You are right i change the gamma curve manually in the jvc projector for watching HDR or DV.

I was so excited to see DV in the OSD that i realised after that i was wrong with my cabling and the integral wired before the AVR.
My AVR is not compatible with DV so, i must bypass the AVR to send LLDV video to the projector.

Futhermore, i wanted to use only one long run of cable between hdfury and pj instead of adding a second cable. So, i changed my wiring with the configuration below and now, all my video sources and audio work!!

The only point to solve now this one:
- the integral stay on the last input selected when i change from input source 0 TO input 1?
Fortunately, i have a goblue and could select the right input with my tablett....or use the switch on the device it self.
I am sure the integral can switch from input-0 to input - automaticelly with the right settings but i can find it???

Daniel
 

Attachments

·
Registered
Joined
·
208 Posts
i use logitech harrmony for remote control but i dont see the input selection in the list for integral 2 menu. Only automatic input switc detection available in logitech?
 

·
Registered
Joined
·
325 Posts
i use logitech harrmony for remote control but i dont see the input selection in the list for integral 2 menu. Only automatic input switc detection available in logitech?
Hi there Please provide the config file from the integral 2 so we can see your settings.
The firmware update for the integral 2 lists all the ir codes for the harmony in a txt file included with the download some are as:

inputsel1:
inputsel1: NEC 0x80 0x0f
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 05d5

inputsel2:
inputsel2: NEC 0x80 0x10
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5

inputmathru:
inputmathru: NEC 0x80 0x11
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5

inputmatswap:
inputmatswap: NEC 0x80 0x12
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5
 

·
Registered
Joined
·
4 Posts
Hi there Please provide the config file from the integral 2 so we can see your settings.
The firmware update for the integral 2 lists all the ir codes for the harmony in a txt file included with the download some are as:

inputsel1:
inputsel1: NEC 0x80 0x0f
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 05d5

inputsel2:
inputsel2: NEC 0x80 0x10
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5

inputmathru:
inputmathru: NEC 0x80 0x11
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5

inputmatswap:
inputmatswap: NEC 0x80 0x12
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5
Hello, I have a smal issue also with my Logitech harmony elite.
The input are 1 or 2 into logitech as I can read them but into my apk 4k integral 2 the input are 0 or 1 . So does the integral input 0 is the 1 into the logitech harmony ?
 

·
Registered
Joined
·
325 Posts
Hello, I have a smal issue also with my Logitech harmony elite.
The input are 1 or 2 into logitech as I can read them but into my apk 4k integral 2 the input are 0 or 1 . So does the integral input 0 is the 1 into the logitech harmony ?
Yes input 1 from our code =0 on harmony and input 2 from our code =1 on harmony.
Hope this helps
 

·
Registered
Joined
·
4 Posts
Yes input 1 from our code =0 on harmony and input 2 from our code =1 on harmony.
Hope this helps
Thanks 👍
My basic configuration is nvidiashield 2019 ( Integral 2 + go blue) , hdmi output 1 to TV Samsung 4k HDR10+ and hdmi output 2 to my Cambridge ( hdmi 1.4) for the audio signal. So, basically , the audio extraction works well.
I use 4k integral to switch to the custom EDID 5 ( LLDV SONY) + custom HDR ON when I have DV VOD on netflix. It's work on HDR nevertheless I am obliged to change the level of contrast enhancer of my Samsung TV after this custum change . Do you have news customs edid dedicated for Samsung TV ?
 

·
Registered
Joined
·
184 Posts
Question: can this device help with color banding issues with projectors that have HDMI bandwidth limitations? I have a Sony VPL-VW675ES, and get a lot of banding when streaming 4K/HDR content due to the 13Gbs HDMI limitation. I have it set to turn off HDR, but I’m still seeing quite a lot of color banding when streaming content. The most recent was the new movie Souls (Steamed at 4K, SDR, using an Xbox Series X, tons of color banding).

I am wondering if it would look any better if I sent a 4K / HDR / 4:4:4 12 bit signal to one of the newer HD Fury devices and had it downscale it to 4K / HDR / 4:2:0 / 8 bit. Would this help, or would the end result look exactly the same since it will still end up at 4:2:0?
 

·
Registered
Joined
·
208 Posts
Hello here is the config.
Hi there Please provide the config file from the integral 2 so we can see your settings.
The firmware update for the integral 2 lists all the ir codes for the harmony in a txt file included with the download some are as:

inputsel1:
inputsel1: NEC 0x80 0x0f
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 05d5

inputsel2:
inputsel2: NEC 0x80 0x10
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5

inputmathru:
inputmathru: NEC 0x80 0x11
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5

inputmatswap:
inputmatswap: NEC 0x80 0x12
0000 006e 0000 0022 0156 00ab 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 003f 0015 0015 0015 0015 0015 0015 0015 003f 0015 0015 0015 003f 0015 003f 0015 0015 0015 003f 0015 003f 0015 003f 0015 05d5
Hello, here is my config .
Please clarify what should I do with all the codes above ? I just want to programm the hdfury and logitech harmony remote control tonuse input 1 for apple tv and input 0 for all others video sources
 

·
Registered
Joined
·
208 Posts
Config
 

·
Premium Member
Joined
·
4,155 Posts
Question: can this device help with color banding issues with projectors that have HDMI bandwidth limitations? I have a Sony VPL-VW675ES, and get a lot of banding when streaming 4K/HDR content due to the 13Gbs HDMI limitation. I have it set to turn off HDR, but I’m still seeing quite a lot of color banding when streaming content. The most recent was the new movie Souls (Steamed at 4K, SDR, using an Xbox Series X, tons of color banding).

I am wondering if it would look any better if I sent a 4K / HDR / 4:4:4 12 bit signal to one of the newer HD Fury devices and had it downscale it to 4K / HDR / 4:2:0 / 8 bit. Would this help, or would the end result look exactly the same since it will still end up at 4:2:0?
I don't know.

Since you mentioned 420 I assume you mean 4K60 as 420 is not legal at 4K24. But 4K60 444 12-bit is not legal either. It would need to be 4K60 422 12-bit.
 

·
Registered
Joined
·
184 Posts
I don't know.

Since you mentioned 420 I assume you mean 4K60 as 420 is not legal at 4K24. But 4K60 444 12-bit is not legal either. It would need to be 4K60 422 12-bit.
Yes - I meant 4k60. I only have the issue while streaming content or playing video games (which is 4k60 rather than 4k24). Projector works like a dream at 4K24.

I get banding at 4K60 and am wondering if a device like this could help.
 

·
Registered
Joined
·
168 Posts
Just dropping in to say this thing is awesome! Got an Apple TV 4k but could not do Dolby Vision and Dolby Atmos at the same time. TV supports DV but would not pass Atmos back through ARC. AVR does Atmos but won't pass through DV to the TV. Not a problem with my bluray as it has two HDMI ports. Just hooked up the Integral 2, fiddled with the GUI a bit and now I have both!

Cheers!
 

·
Registered
Joined
·
325 Posts
Yes - I meant 4k60. I only have the issue while streaming content or playing video games (which is 4k60 rather than 4k24). Projector works like a dream at 4K24.

I get banding at 4K60 and am wondering if a device like this could help.
If you are getting banding because of the reduced color depth then the hdfury would work best to scale the 4k to 1080p 4:4:4 HDR it will look better then the 4k HDR with reduced bitdepth to most people. Color is more important then resolution.
 

·
Registered
Joined
·
7,645 Posts
Hello here is the config.


Hello, here is my config .
Please clarify what should I do with all the codes above ? I just want to programm the hdfury and logitech harmony remote control tonuse input 1 for apple tv and input 0 for all others video sources
The IR codes for inputsel1 and 2 (splitter mode) or matrix thru/swap (matrix mode) are already in Harmony DB, if any problem, just download the latest firmware package, extract it and inside you will find IR code list, just mail them to [email protected] and ask them to add the IR codes to your account after 2 working days you should be able to use the IR codes added to your account.
 

·
Registered
Joined
·
2 Posts
Hello all. I’m in the process of setting up a home theatre with the following hardware;

Pioneer VSX-33 AVR (HDMI 1.4b)
BenQ HT3550 (HDMI 2.0b)
Shield 2019

I will be playing mainly 4K Remux 24p HDR10 files through the shield and would like full HDMI audio on the AVR.

Since AVR Key is no longer available I was looking at buying Integral 2 + HDMI Fibre 30ft cable from HDFury.com store. Will this combo work together and also solve my problem? Is there a benefit in my situation to chose Vertex or Vertex 2?

Thanks!
 

·
Registered
Joined
·
1,574 Posts
Wonder if one can rename the input on Port Selector to my equipmen’s name, rather than just 0,1,2,3 ??? Using a Vertex2 now.
 

·
Registered
Joined
·
7,645 Posts
Hello all. I’m in the process of setting up a home theatre with the following hardware;

Pioneer VSX-33 AVR (HDMI 1.4b)
BenQ HT3550 (HDMI 2.0b)
Shield 2019

I will be playing mainly 4K Remux 24p HDR10 files through the shield and would like full HDMI audio on the AVR.

Since AVR Key is no longer available I was looking at buying Integral 2 + HDMI Fibre 30ft cable from HDFury.com store. Will this combo work together and also solve my problem? Is there a benefit in my situation to chose Vertex or Vertex 2?

Thanks!
Yes that will work perfectly. Vertex2 would allow LLDV>HDR if BenQ is HDR capablebut not DV capable.
If you only up to 2 sources and no need of LLDV>HDR then Vertex1/Integral2 are good choices (make sure you have windows computer for update and advanced utility, or MAC running WIN10 in virtualization)
If you need up to 4 sources and want LLDV > HDR then Vertex2/Diva are better choice and does NOT need Windows computer, they can be controlled and updated from any browser based devices on same LAN network
 

·
Registered
Joined
·
7,645 Posts
Wonder if one can rename the input on Port Selector to my equipmen’s name, rather than just 0,1,2,3 ??? Using a Vertex2 now.
Not yet on webserver, you can do it with Android/iOS APP but only for the Android/iOS APP it won't change it on the webserver.
It might become an available option in future update thus.
 
1281 - 1300 of 1314 Posts
Top