AVS Forum banner
1 - 8 of 8 Posts

·
Registered
Joined
·
238 Posts
Discussion Starter · #1 ·
I have a MX3000 and I can't seem to get it to learn the Monoprice HDMI switch codes. I get good responses when learning but when I test it, it doesnt work. Once every 10 times I test it, it will work.


I put new batteries in the Monoprice remote and Ive used the single and double learn function on the MX3000. It still doesnt work.


Any help would be appreciated.


Thanks


John
 

·
Registered
Joined
·
13 Posts
Try learning the switcher to the MX-3000 again. This time, hold the switcher remote further away from the MX-3000 - about 6". If you see an improvement but not 100%, try learning again and move the switcher remote further.

xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxx

Or use the Discrete codes.......



Monoprice 5x1 HDMI switch

Protocol: NECx1

Main Device #: 8

Sub Device #: 8


EFC

058 Input 1

119 Input 2

249 Input 3

250 Input 4

244 Input 5

052 Input Up

056 Input Down




hope this helps
 

·
Registered
Joined
·
238 Posts
Discussion Starter · #3 ·
Ive tried everything with no luck.


How do I convert the data referenced above into IR codes? I have a URC MX3000.


Thanks
 

·
Registered
Joined
·
664 Posts

Quote:
Originally Posted by theporcupine /forum/post/0


Monoprice 5x1 HDMI switch

Protocol: NECx1

Main Device #: 8

Sub Device #: 8


EFC

058 Input 1

119 Input 2

249 Input 3

250 Input 4

244 Input 5

052 Input Up

056 Input Down

If you can use Pronto hex codes with your remote, and the codes above are correct, these should be the hex codes:


Device Code: 8.8 Function: 15 (Input 1)

0000 006D 0022 0003 00AC 00AB 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0041 0015 0689 00AC 00AB 0015 0041 0015 0E3F


Device Code: 8.8 Function: 18 (Input 2)

0000 006D 0022 0003 00AC 00AB 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0041 0015 0041 0015 0016 0015 0041 0015 0041 0015 0041 0015 0689 00AC 00AB 0015 0041 0015 0E3F


Device Code: 8.8 Function: 25 (Input 3)

0000 006D 0022 0003 00AC 00AB 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0689 00AC 00AB 0015 0041 0015 0E3F


Device Code: 8.8 Function: 31 (Input 4)

0000 006D 0022 0003 00AC 00AB 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0689 00AC 00AB 0015 0041 0015 0E3F


Device Code: 8.8 Function: 28 (Input 5)

0000 006D 0022 0003 00AC 00AB 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0689 00AC 00AB 0015 0041 0015 0E3F


Device Code: 8.8 Function: 12 (Input Up)

0000 006D 0022 0003 00AC 00AB 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0041 0015 0689 00AC 00AB 0015 0041 0015 0E3F


Device Code: 8.8 Function: 13 (Input down)

0000 006D 0022 0003 00AC 00AB 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0041 0015 0041 0015 0016 0015 0016 0015 0016 0015 0016 0015 0016 0015 0041 0015 0016 0015 0016 0015 0041 0015 0041 0015 0041 0015 0041 0015 0689 00AC 00AB 0015 0041 0015 0E3F
 

·
Registered
Joined
·
382 Posts

Quote:
Ive tried everything with no luck.


How do I convert the data referenced above into IR codes? I have a URC MX3000.


Thanks

Unfortunately, the newer versions of the MX Editor software did away with the hex import feature in the Universal Browser.


To use Pronto Hex codes with the MX Editor software, you'll need to first create a .CCF file in ProntoEdit 4.0 (you can download this on the Pronto website). This involves creating a panel within a device with buttons that you can paste the hex codes into. Once you're finished with this, you save the project file (which will be .CCF format) and you can then import the .CCF with Universal Browser and proceed to drag-and-drop the codes onto the desired buttons.


If you need further help with this, you can PM me.
 

·
Registered
Joined
·
238 Posts
Discussion Starter · #6 ·
I converted the hex codes and imported the file to my MX3000.


Same problems.


I dont know what to take the sledgehammer to. The MX3000 or the Monoproce HDMI switch. For now, Ive ordered a Radiient HDMI switch and I will see if that is any better.


Thanks for the help. I appreciate it.
 

·
Registered
Joined
·
13 Posts
Just made a quick . CCF file and imported the buttons into my MX-900.

The input codes work fine.

The UP and Down codes work but seem to want to repeat.

Super Bowl party starting soon, so I'll play with the up and down inputs latter.

If you want the .CCF file pm and I'll send the file to you
 

·
Registered
Joined
·
238 Posts
Discussion Starter · #8 ·
Thanks for the file.


I tried it out and I had the same problems as before.


Today I installed a Radiient HDMI switch which is working fine. Its got a few more features than the Monoprice and is more expensive but it seems to be working just fine. I would recommend the switch to anyone who is looking for a 4X1 HDMI switch with RS232.


Thanks again for all the help.
 
1 - 8 of 8 Posts
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top